The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Questions And Answers for NTW4600YQ0
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Melvin
March 24, 2020
How to tell if your circuit board is bad
For model number NTW4600YQ0
Hello Melvin,
Thank you for your question. First check all the connections to be board to make sure they are secure and no visual damage. Next, inspect the board itself for any visual damage. You can test it with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. We hope this helps.
Hi, my washer has been off balance a lot lately. Making the awfullest loud noises. And today, I had a small load in. And it sounded like a loud balloon popping. Any ideas? It's filling, draining, but not spinning. Is there a belt that could have broke? Haven't got underneath to look yet! Thank you
For model number NTW4600YQ0
Hello Karen, Thank you for the question. Normally this is caused by a damaged Suspension Rod. We suggest checking the rods for wear or damage. It may have also put strain on the belt causing it to snap. We hope this helps!
Is It possible to bypass the lid lock on this washer
For model number NTW4600YQ0
Hello Steve, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS3497627. Thank you for your inquiry, good luck with this repair!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.