Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will ...
This is a high limit thermostat designed for microwaves, ranges and ovens. Made of plastic and metal, this thermostat is designed to open the electrical circuit for your appliance when it reaches a sp...
This convection fan motor assembly is designed to circulate hot air throughout the oven cavity, promoting even heat distribution for more consistent baking and roasting results. By keeping air moving ...
This surface element triple burner infinite switch, or regulator control, is located in the control panel of your range oven. It is responsible for turning the surface element on or off and adjusting ...
This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It preven...
This energy regulator, more commonly known as a surface element control switch or burner switch is compatible with various models of Samsung ranges. It consists of the switch housing and a metal shaft...
This stainless steel wire rack is a sturdy platform for baking or roasting food, making sure heat circulates evenly. It measures approximately 7/16 inches by 24 3/4 inches and is usually found inside ...
This display board is for ranges.
Display board receives signals from the control board and displays the time and temperature settings.
Unplug the range or shut off the circuit breaker before in...
This genuine OEM left-threaded convection fan motor is responsible for spinning the fan blade, ensuring even circulation of hot air within your oven for consistent cooking. It is typically located beh...
Enhance the functionality of your Samsung range oven with this genuine Electronic Control Board. This brand new, high-quality part was meticulously designed for Samsung ranges, ensuring a flawless fit...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dominique
January 6, 2020
Hello, i need a wire rack for my electric range
For model number NE59J7630SS
Hello Dominique, thank you for your question. The oven rack for this unit is PartSelect Number PS7321783. Please enter the part number into the site for current price and availability. Good luck with your repair!
Did this question help you?
Thank you for voting!
James
December 22, 2022
After selecting the oven, whether it be bake or convection or any other then you select the temperature, once you hit the start button the screen goes blank then back on seconds later almost like there was a power outage. Any assistance would be appreciated.
For model number NE59J7630SS
Hi James, thank you for reaching out. It seems that the display control board, part number PS11720419, is defective and needs to be replaced. If you require assistance to place an order, please contact customer service. We hope that helps!
Door does not close tight , specially when on convection mode
For model number NE59J7630SS
Hi Robert, thank you for reaching out. Based on the description that you have provided, we would recommend checking the door latch, part number PS12086347, as it is the most likely cause of this issue. We hope this information helps!
Hello Koheer, thank you for getting in touch. The error code c-d0 indicates that a button has been pressed and held for too long. We would recommend checking the membrane switch, part number PS11720662, to solve the problem. A malfunctioning membrane switch can most probably cause this problem. We hope this helps!
My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the
... Read moreissue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!
I removed the control panel with a Phillips screwdriver and unplugged the burner switch and replaced the new switch and put the control panel back in place and turned on the burner and it worked as it should.i realized that I only would have only had to remove the 4 screws on the bottom of the control panel. All I would have had to do was
... Read more just take those 4 screws out and remove the switch control knob and the two screws that held the switch in. Am very happy with the results
This oven has two fans that counter rotate. One spins clockwise, the other counterclockwise. Because of this, the motors and the fan blades are different. The schematic shows the counter clockwise rotating fan with a right hand threaded shaft/nut on the bottom and the clockwise motor and fan with the left hand nut on the top. My range
... Read more had the motors in the exact opposite orientation, but the fan blades on the motors as shown on the schematic. The incorrect assembly at the factory (I bought new in the box, so I know this is the first repair) meant that nether fan blade was turning the correct direction. So do yourself a favor, be sure you’re buying the right motor (clockwise or counterclockwise) and be sure you put the right fan blade on the right motor. The Samsung motor ending in F is the counterclockwise motor that has the right hand threaded shaft the clockwise motor with the left hand threaded shaft ends in E.
