NBXR453EV0AA Hotpoint Dryer - Overview
Sections of the NBXR453EV0AA
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
DRYER FRONT BEARING WHITE 2PK
PartSelect #: PS17137205
Manufacturer #: WE03X37318
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
$17.15
In Stock
Door Switch
PartSelect #: PS2344321
Manufacturer #: WE4M415
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
$39.46
In Stock
Nut
PartSelect #: PS267646
Manufacturer #: WE2M96
This fastening nut secures components firmly in place, helping maintain proper alignment and safe operation. It is commonly used as a replacement when original hardware is stripped, lost, or damaged.
$18.30
In Stock
Timer Resistor
PartSelect #: PS267964
Manufacturer #: WE4M255
Looking for a way to keep your washing machine running smoothly? Our GE Platform Bearing Retainer & Fasteners could be just what you need. This particular piece is not just a part, it's actually the h...
$43.16
In Stock
Cycling Thermostat
PartSelect #: PS267949
Manufacturer #: WE4M216
This thermostat is located on the blower wheel.
$88.47
In Stock
Front Panel Assembly
PartSelect #: PS10059171
Manufacturer #: WE49X22295
Are you struggling with uneven heat distribution while cooking on your GE range? Does it leave one side of your pan hot, while the other side remains barely warmed? Don't worry! We've got the answer t...
$168.49
In Stock
Temperature Switch
PartSelect #: PS2337898
Manufacturer #: WE4M403
This is a rotary style temperature switch for a washer.
$130.14
Special Order
Questions And Answers for NBXR453EV0AA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the NBXR453EV0AA
[Viewing 4 of 4]Noisy
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would not start
The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a pow
... Read more
er fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website.
Read less
Parts Used:
-
Joshua from Dallas, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
92 of 140 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Dryer would not start
Doing some simple troubleshooting with the volt-ohm meter I determined that the door switch was failed.
The replacement door switch restored the motor circuit keeping my dryer in action.
The replacement door switch restored the motor circuit keeping my dryer in action.
Parts Used:
-
David from Curtice, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
60 of 107 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer was cutting off completely.
The problem was intermittent. It only happened when the unit was first started. After it was restarted it usually worked until the load was dry. I looked at the schematics and saw that only the hi-temp therostat and the motor overload could stop the dryer completely. I put my volt meter on the hi-temp thermostat and ran the dryer. Wh
... Read more
en the dryer stopped I realized the hi-temp therm. was tripping. I read the web site help for this symptom and the suggestion was the bias therm.
I replaced it and the unit worked.
I replaced it and the unit worked.
Read less
Parts Used:
-
Stephen from Mechanicsville, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
32 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!