Models > MVWX700XL1

MVWX700XL1 Maytag Washer - Overview

Sections of the MVWX700XL1

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Lid Latch Assembly – Part Number: W10404050
Lid Latch Assembly
★★★★★
★★★★★
(35)
PartSelect #: PS3497627
Manufacturer #: W10404050
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
$45.21
  In Stock
Drive Belt – Part Number: WPW10006384
Drive Belt
★★★★★
★★★★★
(19)
PartSelect #: PS11747978
Manufacturer #: WPW10006384
The main drive belt is designed to ride on the pulley until the basket gets up to speed.
$33.51
  In Stock
Washer Drive Pulley – Part Number: W10721967
Washer Drive Pulley
★★★★★
★★★★★
(20)
PartSelect #: PS10057144
Manufacturer #: W10721967
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$57.16
  In Stock
Tub Centering Spring – Part Number: W10400895
Tub Centering Spring
★★★★★
★★★★★
(8)
PartSelect #: PS3497596
Manufacturer #: W10400895
Tub centering spring
$9.92
  In Stock
Suspension Rod Support – Part Number: W10440729
Suspension Rod Support
★★★★★
★★★★★
(18)
PartSelect #: PS3502189
Manufacturer #: W10440729
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension...
$9.44
  In Stock
Washer – Part Number: WP3949550
Washer
★★★★★
★★★★★
(1)
PartSelect #: PS11742027
Manufacturer #: WP3949550
This part goes on the agitator retaining bolt.
$13.40
  In Stock
Touch-Up Paint - White – Part Number: 72017
Touch-Up Paint - White
★★★★★
★★★★★
(1)
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.44
  In Stock
Shift Actuator - 120V 60Hz – Part Number: WPW10006355
Shift Actuator - 120V 60Hz
★★★★★
★★★★★
(24)
PartSelect #: PS11747977
Manufacturer #: WPW10006355
This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.
$68.13
  In Stock
D-Shaped Knob Insert – Part Number: WP8536939
D-Shaped Knob Insert
★★★★★
★★★★★
(1)
PartSelect #: PS11746209
Manufacturer #: WP8536939
This insert is sold individually. Knob not included. Knob is sold separately.
$10.56
  In Stock
Hose Clamp – Part Number: WP285655
Hose Clamp
★★★★★
★★★★★
(2)
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$8.79
  In Stock
Lid Bumper – Part Number: WP9724509
Lid Bumper
★★★★★
★★★★★
(4)
PartSelect #: PS11747040
Manufacturer #: WP9724509
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
$7.76
  In Stock
Drain Pump - 120V 60Hz – Part Number: WPW10276397
Drain Pump - 120V 60Hz
★★★★★
★★★★★
(11)
PartSelect #: PS11751719
Manufacturer #: WPW10276397
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time
$142.37
  In Stock

Questions And Answers for MVWX700XL1

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

4 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Todd
    January 7, 2020
    Why doesn,t my washer spin it's not the belt i cked it lmk thank u
    For model number MVWX700XL1
    Hello Todd and thank you for writing. As it is not the belt, it certainly sounds like it could be a faulty shift actuator PS11747977 and/or drive pulley PS10057144, you should check for signs of damage, and replace if necessary. We hope this helps. Please contact us anytime if you require further assistance.

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Todd
    January 7, 2020
    Why doesn't my washer spin.
    For model number MVWX700XL1
    Hello Todd, thank you for the question. The most common reason is a broken Belt PartSelect Number PS11747978. We hope this helps!

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Robert
    November 30, 2021
    How do you open the lid to replaces latch assembly
    For model number MVWX700XL1
    Hi Robert, Thank you for the question. Here is a link to our video on how to replace the lid lock. It should be of some help. Good luck with the repair!
    play video

    Was this helpful?
    Thank you for voting!
    Pam
    September 23, 2022
    Why my water want drain and spin?
    For model number MVWX700XL1
    Hello Pam, thank you for contacting us. We would recommend checking the following parts to fix your issue: Drain Pump, part number PS11751719, Drive Belt, part number PS11747978, Shift Actuator, part number PS11747977, and Lid Latch Assembly, part number PS3497627. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.

    Was this helpful?
    Thank you for voting!
    Related Parts:

      Common Symptoms of the MVWX700XL1

      [Viewing 14 of 14]
      Noisy
      Fixed by
      these parts
      Show All
      Shakes and moves
      Fixed by
      these parts
      Show All
      Pumps but will not spin
      Fixed by
      these parts
      Show All
      Will not agitate
      Fixed by
      these parts
      Show All
      Will Not Start
      Fixed by
      these parts
      Show All
      Leaking
      Fixed by
      these parts
      Show All
      Will not drain
      Fixed by
      these parts
      Show All
      Lid or door won’t close
      Fixed by
      these parts
      Show All
      Spins slowly
      Fixed by
      these parts
      Show All
      Burning smell
      Fixed by
      these parts
      Show All
      Lid or door will not open
      Fixed by
      these parts
      Show All
      Will not stop filling with water
      Fixed by
      these parts
      Show All
      Timer will not advance
      Fixed by
      these parts
      Show All
      Will not fill with water
      Fixed by
      these parts
      Show All
      Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
      Lid Lock light blinking, machine will not start
      A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
      Parts Used:
      Shift Actuator - 120V 60Hz
      • David from Los Alamos, NM
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Screw drivers
      302 of 375 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Defective lid latch - Cabrio Washer
      The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
      Parts Used:
      Lid Latch Assembly
      • William from Wakefield, RI
      • Difficulty Level:
        Very Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      81 of 97 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Noise on bottom of Washer louder as time went on. 1 1/2 years
      Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
      Parts Used:
      Drive Belt Washer Drive Pulley
      • Jerry from WALLA WALLA, WA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers, Socket set
      63 of 81 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!