Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging th...
This washer lid switch is a critical safety component designed to halt the spinning motion of the tub when the lid is opened. Its primary function is to prevent accidental contact with moving parts du...
This suspension rod kit is a genuine OEM kit specially designed for washing machines. Each kit includes a set of 4 rods, 4 suspension balls and 4 bushings. The suspension rods are responsible for supp...
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the ...
This shift actuator is a genuine replacement component designed for top-load washing machines. It plays a critical role in transitioning the washer between agitation and spin cycles by shifting the tr...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
$20.36
Special Order
Questions And Answers for MVWX500XW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Staff
August 23, 2021
Why doesn't my washer complete the cycle?
For model number MVWX500XW0
Hello,
Thank you for your question. If your washer does not complete a cycle, the part that fixes the issue most of the time is the lid switch. The lid switch is a safety feature found on most top loading washing machines and it supplies power to the electronic control board and the motor circuits. To verify if it is working correctly, you will need to remove it from the washer and test it with a multimeter for continuity. Unplug the washer from the electrical outlet before performing any tests on it. Before removing it, begin by ensuring that no levers or actuators are damaged or sticking and that the switch is being activated mechanically when the lid is closed. If no issues are found when performing the above checks, remove the switch and set your multimeter to the Rx1 setting. While pressing and holding the switch button, place the probes on the switch’s terminals, you should receive a reading of zero. If you receive a different reading, you will need a replacement lid switch. If the lid switch is fine, there are some other parts that you will need to check to see which one is causing the issue. You will also need to check the electronic control board, the timer knob, the drain pump and the water inlet valves. You will find the information on how to test these parts under Free Repair Help and Instant Repairman on our website. We hope this helps! Good luck with the repair!
Hi, there is grease in the drum of my Maytag washer model mvwx500xw0 serial number c04736493. Why is it there? What do I need to do? Is mainly within a 6" 8" section.
For model number MVWX500XW0
Hello Kate, Thank you for the question. This sounds like the Seal for the Tub has worn down. When the Seal wears down the oil and grease can make their way out of the transmission then that oil and grease can enter the washing machine's drum during a wash cycle. We suggest checking the seal for wear. We hope this helps.
My washer is the Maytag bravos top loading it will go through all the cycles except spin it will pause then skip and go to end but soothes are soaking wet. The belt is fine was not broken what else could be the problem?
For model number MVWX500XW0
Hello Linda,
Thank you for your question. Our sources suggest replacing the shift actuator under part PS11747977 for your model to fix the issues. We hope this helps.
Machine locks lid, starts sensing and the motor strains to move. Then stops and hums with lid lock light flashing. Cant power off. I have to unplug and try again, Have any ideas? I thought Maybe shift actuator and or capacitor. Motor and tub spin free!
For model number MVWX500XW0
Hello Frank, Thank you for the question. This sounds like an issue with the Lid Latch Assembly. The point of the lid switch is for the tub to stop spinning when the washer lid is opened. We hope this helps.
Hi Antonio,
Thank you for your question. If your washer grinds on the spin cycle, the washer may not be level or the washer has been overloaded. The grinding noise may also be caused by either a worn or damaged drive pulley or bearing. The bearing for your washer is sold with the gearcase. If you need help placing an order for a part, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
