Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your wa...
This kit (Medium Cam Agitator Repair Kit, Washer Agitator Cam Repair Kit, Cam Agitator) is used to repair the agitator. These parts are located inside the agitator auger near the top. You will need t...
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is ...
This is a genuine OEM thrust spacer for your washer, and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in color. It is used in...
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollabl...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, a...
This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.
$9.62
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for MVWC300VW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Susan
November 16, 2022
How many cubic feet is this washing machine. Trying to replace it and would like something at least the same size. Thank you
For model number MVWC300VW0
Hello Susan, thank you for getting in touch. Your washing machine has a capacity of 3.2 cubic feet and measures 42'' H by 27'' W by 25.5'' D. We hope this helps!
3 people found this helpful.
Did this question help you?
Thank you for voting!
Hussein
March 5, 2020
Every time the washer spain's all the lights in the house goes on and off and they blink. Do u think it’s the motor or something else
For model number MVWC300VW0
Hi Hussein, thank you for your question. You may want to check the plug and fuse that you have connected to the machine. It might be that you do not have the proper outlet that can handle the appliance being plugged into it. Otherwise you could look at your motor and your control board perhaps being the issue. Good luck with your repair.
1 person found this helpful.
Did this question help you?
Thank you for voting!
Jeffrey
February 16, 2023
Hey there just wondering if you had a trouble shooting guide.
My washer seems to be making a buzzing sound and jot actually spinning and draining the water.
Im fairly handy with mechanics so i was wondering if you had any ideas on where to start before i go and replace it
For model number MVWC300VW0
Hi Jeffrey, thank you for reaching out. We would recommend checking the drain pump for any socking. If this is not the issue, then you may need to replace the drain pump, part number PS11741239, and drive motor, part number PS11743427. We hope this will solve your problem!
I'm experiencing a hot water leak when the tank is filling up; I did not see a leak anywhere at the inlet hose; what might be the cause & what part(s) may need replacing?
For model number MVWC300VW0
Hello Paul, thank you for reaching out. Based on our understanding of the issue, we would suggest you checking the water inlet valve, part number PS11742194. We hope this helps, good luck with this repair!
When I start a cycle, the washer just keeps filling with water and doesn't stop. Spin and drain work fine as does hot and cold.
I have to manually stop it so it doesn't overflow.
For model number MVWC300VW0
Hi Joe, thank you for your question! It sounds like there may be an issue with the water level switch, part number PS3408163. We would recommend replacing it to fix the issue. We are sure this will help!
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs. Slip the new cogs into the underside of the cup, and slide the cup back down in the a
... Read moregitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out). Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
The instructions came with the repair kit, it was fairly simple and straight foward.
One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repai
... Read morer kit.
Very easy do-it-yourself repair! Took about 20 minutes because I was being cautious. Next time I could do it in 5 minutes.
On top of the agitator is a flat cap that is held in place by the friction of an o-ring, there are no fasteners. I would imagine one could get under the lip with a small screwdriver or butter knife to pop it off but I chose simply using my fingernails so as to not disfigure the cap. Under the cap you will find the head of the only bolt
... Read morethat holds the assembly together it is a 7/16 head and because it is in a 4" deep well your will need a 6" extension for your ratchet. Once the bolt is out the top of the agitator, the assembly with the cogs removes by hand. Set the assembly upside down on the counter, slide the black plastic ring off, pull the cogs out with your fingertips, install the new cogs put a new black ring on and set the assembly back in the agitator. Reinstall bolt. As the bolt is down in a tube, you cannot set it in place with your fingers and it will fall out of the socket. To hold the bolt in the socket during positioning you can either put a gob of Vaseline on the bolt head to hold it in the socket or form a small piece of paper over the bolt head and set it into the socket, the friction of the paper will hold the bolt into the socket. Took me less then 10 minutes, good luck
