Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is an inlet valve for your washing machine. The inlet valve is an electrically controlled valve with a solenoid that opens and closes as needed, during the water filling cycle of the washing mach...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
This agitator assembly is an authentic OEM part that is compatible with various models of washing machines. It consists of a central shaft with a series of fins attached to it. When the washer is oper...
Introducing the Whirlpool Washer Washplate Screw - your reliable solution for fixing broken or loose washplates in your washing machine. This OEM genuine part, compatible with distinct models of Whirl...
This is an impact absorber, also known as a sound dampening pad, for washing machines. This sound dampening pad attaches to the top of your washing machine drum to reduce the severity and harshness of...
This clutch slider kit is genuine OEM replacement kit that fits in various models of washing machine. It is a part of the transmission system in your washer which is responsible for controlling the mo...
This drain pump is specially designed to fit in top load washing machines. It is responsible for removing water from the washer tub during the drain cycle and directing it to the household plumbing sy...
This lid hinge is a genuine OEM replacement part for your washing machine. This hinge is for the left side of your lid, although it is a good idea to replace btoh hinges at once. The hinge holds up th...
$21.45
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for MVWB765FC2
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Georgette
February 18, 2023
When I press the start button my lid is not locking. Once I get it to lock it will wash half of the time and then the lid unlocks and stop the washer from washing. Is this fixable if so is there a DIY video to replace the lock.
For model number MVWB765FC2
Hi Georgette, thank you for reaching out. We would recommend checking the lid lock assembly, part number PS11731620, to solve the issue. We have included a link to one of our YouTube videos that you may reference on how to install the lid switch. The washer in the video may appear different from yours, but it will give you a general idea on how to install the part. We hope this helps with the repair!
What can cause the washer to have no power to turn on, when outlet is good and green light on mother board is on?
For model number MVWB765FC2
Hello Christa, thank you for contacting us. We recommend checking the wire harness connecting to the control board. Make sure all connectors to the control board are firmly connected and no wires are damaged. If any of the connectors or wires are damaged, you will need to replace the wire harness, part number PS12349035. If the wire harness is okay, you may need to replace the control board, part number PS12347691. We hope this solves your problem!
My washing machine starts to squeal very loudly a few moments after I press the start button. What part would I need. I thought it would be a belt or tensioner, but this washing machine has neither.
For model number MVWB765FC2
Hi Jeff, thank you for reaching out. The loud noise could be caused by worn-out or damaged bearings in the washer. They come attached to the gear case, part number PS12741641. You may need to replace it to fix the issue. We hope this solves your problem!
My maytag washer had finished its cycle and board has the oxi/ sanitize light on with sensing and start light with deep clean light i have changed the control board , same lights appear as soon as its plugged in no other buttons or controls appear to work ? Do not think its the door latch cause I should be able to select something new on controller ? Can not even put it in diagnostic mode to check if there is a code?
For model number MVWB765FC2
Hello James, thank you for getting in touch. According to the description of the issue, the control panel or console, part number PS12347927, is faulty and will need replacement. We hope this helps.
Washer sounds like a jet engine during the spin cycle. Very loud noise when it spins!
For model number MVWB765FC2
Hi James, thank you for contacting us. The issue could be with the tub bearings. They come attached to the gearcase, part number PS12741641. You may need to replace it to fix the issue. We hope this sorts out your problem!
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate
... Read more( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Removed two screws on back of lid to raise top removed tub one bolt and one spanernut pulled tub lowered top reinstalled screws laid washer down to get to bottom of washer unplugged wiring removed four bolts pulled gear box and motor removed motor from gear box installed motor on new gear box reassemble washer
