Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This is a door hinge, which allows for your washer door to properly shut during the washing cycle, and open after it is finished. If your door hinge is bent or broken and not allowing the door to shut...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
Having trouble with your freezer?s efficiency? Your GE Freezer Door Gasket might be the solution you?re looking for. This is an official replacement part designed to perfectly seal your freezer door. ...
This is a dryer door hinge cap, also known as a bushing, which is a durable plastic cap that is installed on the door hinge and is used to allow your dryer door to operate smoothly when opening and cl...
This hose attaches to water pump assembly.
NOTE: As per the manufacture if the washer has an Eco Ball, it's no longer needed when the new hose is installed.
This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside t...
The leveling leg locking nut is an OEM replacement fastener for use in dryers and washers. It has a head diameter of 3/8 inches and a thread pitch of 16 threads per inch. The nut secures the leveling ...
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
This part regulates the temperature of the water in the tub. The sensor is located in the heating element.
$34.74
In Stock
Order now and your part arrives by Mar 30
Questions And Answers for MHW8000AW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeff
January 11, 2024
Hi, I have a Maytag front loading washing machine model Maxima XL model# mhw8000awo, the bearing in rear housing is leaking. The bearing is pressed into a metal housing which the stator attaches by 3 bolts. This appears to be the outer drum rear section. My question is: what is the kit part number is to replace the bearings?
For model number MHW8000AW0
Hello Jeff, thank you for the question. You may need to replace the rotor, part number PS3490258, to fix the issue. We hope this helps!
I'm getting an error code E01 F09.
How do I access and clean the filter?
Can you access by removing the front panel?
For model number MHW8000AW0
Hi Carolyn, thank you for your inquiry. F09 E01 means that your washer is not draining properly. To access the drain pump filter, you will need to remove the bottom panel. If cleaning the filter does not help, you will need to replace the drain pump, part number PS11755869. Good luck with this repair!
Removed the top (3-4 screws at back). Flowmeter has 2 hoses with hose clamps. Removed with plyers. Simple electrical connector removed.
Reversed procedure. Running perfect now.
How did I know it was the flow-meter? Read the service manual as possible causes to narrow it down. Disassembled old flowmeter and cleaned
... Read more. That fixed for awhile. Problem came back, could 'tap' on flowmeter to temporarily fix. This convinced me that was indeed the problem.
The flowmeter is just a simple vane that moves as water flows across it, and sends pulses each time it rotates. If it 'sticks' then the computer doesn't think any water is coming in - hence the error. Tapping on it would 'unstick' long enough to confirm problem.
Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.
Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machi
... Read morene requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.
First some background. The door locked up the first time when appliance was less than one year old. The "Maytag Repairman" finally succeeded in getting the door open after propping up the front of the machine and fumbling around underneath for a period of time and then assured me the problem was solved. The problem recurred less than a
... Read more year later, and I called another repairman who seemed to have an easier time of it, and charged $293.42 to replace the water level switch. About six months later the same problem recurred and I took the cover off the top of the machine and found there a booklet "For Service Technician's Use Only". VERY HELPFUL. Told how extremely easy it was to unlock door - took about five seconds. Replacing the switch itself involved pulling one tubing off and disconnecting one elec connection from old switch and replacing on new switch. Total cost $50 plus a few dollars for shipping.
