MGD3100DW0 Whirlpool Dryer - Overview
Sections of the MGD3100DW0
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Leveling Foot
PartSelect #: PS1609293
Manufacturer #: 49621
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
$6.40
In Stock
Idler Pulley with Bracket
PartSelect #: PS11726337
Manufacturer #: W10837240
The idler pulley with bracket ensures proper tension on the dryer’s drive belt, allowing the drum to spin effectively. This assembly includes the pulley and arm, making it ideal for replacing a worn o...
$27.36
In Stock
Blower Wheel
PartSelect #: PS11743811
Manufacturer #: WP697772
The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over ...
$49.50
In Stock
Liquid Propane Gas Converter
PartSelect #: PS16875225
Manufacturer #: W11581317
This gas conversion kit is used to convert natural gas burners to liquid propane in dryers. If your dryer will not start, heat, or there is an unusual smell, replacing this part can be a solution to t...
$58.42
In Stock
Stacking Kit
PartSelect #: PS888067
Manufacturer #: 8541503
This kit comes with 2 adhesive pads, 2 brackets and 4 screws. This is for stacking the appliances vertically - dryer over washer.
$46.34
In Stock
SEAL
PartSelect #: PS12711436
Manufacturer #: W11310035
Enhance the efficiency of your clothes dryer with this genuine OEM Whirlpool Dryer Door Seal. Specifically designed for Whirlpool clothes dryers, this durable, high-quality seal also works effortlessl...
$62.60
In Stock
Drying Rack
PartSelect #: PS346849
Manufacturer #: 3406839
Need to dry shoes or sweaters without the tumble? This handy drying rack makes it easy. It fits right into the back of your dryer—no tools needed—and stays still while the drum spins, so your items ge...
$56.33
In Stock
Side and Bottom Vent Kit
PartSelect #: PS3633049
Manufacturer #: W10470674
This kit is used for the bottom and side exhaust. The kit includes both the straight and elbow vent.
$72.00
In Stock
Hinge
PartSelect #: PS11775346
Manufacturer #: W11051465
The dryer door hinge assembly is an essential part of your clothes dryer, providing the support needed for the door to open and close smoothly. This hinge assembly is installed on the front panel of t...
$80.82
In Stock
RACK-DRY
PartSelect #: PS1487158
Manufacturer #: 8212450A
Maximize the efficiency of your Whirlpool 27 inch dryer with this genuine OEM drying rack. It's specifically designed for dryers with lint screens located inside the front door opening. What makes thi...
$72.00
On Order
Questions And Answers for MGD3100DW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the MGD3100DW0
[Viewing 8 of 8]Noisy
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Door Sags
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
converting to LP gas
First I removed the front panel which allowed access to the burner assembly. Then I removed the gas connector and elbow from the back of the dryer. Then I removed 2 screws that hold burner assembly in place and 2 screws that hold an angle brace for the burner assembly. Had to loosen the screw that clamps around the gas pipe holding it in
... Read more
place clear in the back inside dryer housing. Unplugged all wiring connectors, then I removed the burner assembly and removed the 2 screws holding the burner tube to the valve. Remove the orifice and replaced with the proper size for LP gas. Then removed the blocking pin and replaced with one for LP gas. Then reassembled in reverse order. Actually pretty easy.
Read less
Parts Used:
-
Robert from Tenino, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set, Wrench (Adjustable)
30 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
craked blower motor
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Parts Used:
-
joe from cheswick, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
63 of 144 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to change rear exhaust to the side to fit dryer into my closet.
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Parts Used:
-
Mark from San Diego, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
44 of 91 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!