This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the ro...
The heating element (Flat Can Heating Element 5400W, Heating Element, Whirlpool Dryer Heating Element, Dryer Heating Element) provides heat to the dryer. It is metal and measures 10.5 inches long, 7.5...
A dryer high-limit thermostat (High Limit Thermostat, Hi-Limit Thermostat, Dryer High-Limit Thermostat) is a switch that is actuated by temperature change. This high limit thermostat acts as a safety ...
This white OEM dryer door handle is used to open and close the dryer's door. Comprised of plastic and 6-by-2-inches in dimension, the handle is sold individually and attaches to the dryer door. Your d...
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is l...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
This seals Includes adhesive. This part helps seal the drum to prevent hot air from escaping.
$64.69
In Stock
Questions And Answers for MED6200KW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carolyn
March 22, 2023
Hello. Do you have a periscope Vent for the Maytag Electric dryer, Model #
MED4500MW?
For model number MED6200KW0
Hello Carolyn, thank you for reaching out. We have researched the model and found that the part you are looking for is the Metal Vent Periscope, part number PS2347217. If you require assistance to place an order, please contact customer service!
I need a screw for my dryer door. Not for the hinges but that holds the front of the door and back of door together. The installers dropped one and couldn’t find it don’t tell me and I noticed it! I have had so many problems with the store I bought it from I don’t want to go back to them when my dryer is less than a month old!
For model number MED6200KW0
Hi Kristie, thank you for reaching out. The screw, part number PS11742718, is compatible with the given model. We hope this is what you were looking for!
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element wi
... Read moreth an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
The repair was easy. the most time consuming part was vacuuming the dust from the back of the Dryer, The repair required removing screw from the back panel of the dryer. Then removing screws from the heating element and unplugging the wires. The only moderately diffculy part was swapping the sensor form the old element.
Moved dryer from wall,disconnected power. Unscrewed the 12+ sheet metal screws holding on the back cover. Located heating element, remover it's two sheet metal screws and pulled down on the element to remove. Disconnected the two electrical leads from element and went to the top of Dryer. Do not remiember if told to remove the temptur
... Read moree kill button was easy to see that it was needed on new element. Moved high tempeture senson to new element. Reversed steps to install new element. Replaced back cover, pluged in and powered up. Works like a champ. Thanks for the price on the part and the video which started me on the right track. I'll be back !!