This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack wil...
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$64.02
In Stock
Questions And Answers for MDBH979SAM0
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robin
February 10, 2020
Will not finish cycle. Doesnt shut off or stop washing ..help
For model number MDBH979SAM0
Hello and thank you for writing.
It certainly sounds like it could be a faulty pump PS11757388 and/or possibly a malfunctioning door latch PS8770043 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
Hi Denise,
Thank you for your question. The part number listed under your model number for the electronic control board is PS3633161. You may order it online or by calling customer service. Thank you and have a great day!
Dish washer keeps flipping breaker and sometimes has a slight burning smell. Nothing is on the heating element
For model number MDBH979SAM0
Hello Justin, Thank you for your inquiry. Researching the model number that you have provided, this could be caused by an issue with the motor and pump slowly breaking down and/or overheating and causing a short and a burning smell. Check the wiring going to the circulation pump and motor for any visible damage, and check the pump housing for any visible damage and test it with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. Good luck with your repair.
Hi
I have a Maytag dishwasher Model #MDBH979SAM0.
It takes several attempts to get the dishwasher to start washing. It will attempt to start and then stop with flashing lights. At that point, I have to hit cancel, let it drain, and start over with another attempt.
It can take a number of tries to get it going (never on the first attempt), but it does finally start after a while. This is the case on all wash settings.
Once it starts washing, it seems to do a good job, but it will not stop on it own. The cycle continues to run until I hit the cancel button to stop it.
Let me know what can be done to fix this.
thanks
s
For model number MDBH979SAM0
Hi Stephen, thank you for contacting us. To solve this issue, the following parts need to be checked: the wire harness, part number PS11754261, and the electronic control board, part number PS3633161. We hope this solves your problem!
Repaiman replaced gasket around door, machine still leaks from bottom of door on the left side. What else could cause this machine to leak???
For model number MDBH979SAM0
Hello Marilyn, thank you for your inquiry. You will need to replace the lower door seal, part number PS11755651, to fix the leakage issue. We hope this is helpful!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull
... Read more it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.