Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This door latch (Dishwasher Door Latch Assembly, Door Latch Assembly, Latch Assembly) is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open. It is located on ...
This door latch, used in dishwashers, is located at the top of the door and locks the door shut when the dishwasher is working. If the door will not close or is damaged, changing the latch could be th...
The fold away tine pivot or clip holds the tine rows in place. This part is made of gray plastic and is approximately 3 and a half inches in length. Some dishwasher models will have fold away tine row...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This part is essential in your dishes getting clean during the wash cycle. If there is any debris or a tear in the filter, it can cause extra buildup and, therefore, causing dirty dishes.
This is a part for your dishwasher. The door cable link helps to keep the door steady and give support to the weight of the door when it is being opened or closed. If you notice the door latch has fai...
This is the replacement water valve for your dishwasher. The water inlet valve connects to the water source and solenoid wires, and ensures the tub has the right amount of water entering it. If your d...
The hardest thing was figuring out that you only need to purchase the latch handle because it only comes as a complete latch assembly, why they even list the latch assembly as a separate part in the parts list stupid. (you get the handle and latch already put together and it cost less than the latch assembly without the handle). Anyway al
... Read morel you need to do is disconect the power from the dishwasher (unless you like to live dangerously like me) take your drill with the correct size torx bit and remove all the screws on the inside door pannel (the top center two screws actually hold the latch assembly in place). Disconect the 4 wires from the old part and reconect them to the new part and reinstall all the torx screws being careful not to strip the plastic threads that they screw into if you are using a drill. Whole process takes less than 5 minutes. I am surprised that Maytag used such a flimsy handle assembly in their dishwashers since they are supposed to have the repair men with the most time on their hands. They probably sell just as many handle assemblies as they do dishwashers that have this particular part in it, probably more since you will probably have to change it 2 or 3 times during the life of the unit.
I Followed others' instructions already posted to replace the whole handle assembly. In particular, use a big screwdriver placed against the bottom of the handle and whack the grip with the palm of your hand to get the handle to move back to the open position so you can open the door and start the job. I am no handyman, but this fix was
... Read more easy, about 30 minutes in all, most of which was spent figuring out which breaker to pull so as not to get shocked. One note of caution: use the correct screwdriver attachment (not a Phillips head or regular, but a star or something- see I am not a handyman but I do have a $15 screwdriver set that just paid for itself 10 times over!).
Remove the 8 or 9 torx screws holding the inner and outer door assembly together (leave the bottom screws in), lift the old handle assembly out, transfer the switches to the new handle assembly, and reassemble door.
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Maytag Dishwasher")
