This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.
This is a seal, but you may also know it as a door gasket and it is for your dishwasher. The seal forms a watertight barrier between the door and the dishwasher tub, deterring water from escaping duri...
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$74.60
In Stock
Questions And Answers for MDB4949SDH3
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
January 31, 2020
Dishwasher fills but doesn't run. Then it makes the ticking noise like when it's supposed to go through cycles.
For model number MDB4949SDH3
Hello Michael,
Thank you for your question. Our sources suggest replacing the overfill control switch under part PS11750031 for your model to fix the cycle issues. We hope this helps.
Beige or white plastic piece in the back of the dishwasher that sits over a larger grey piece came off and appears to be melted on the corner. There’s 2 numbers on this piece w10323076 and pp-td20/teo. I cannot find this in diagrams or any parts list. Thank you
For model number MDB4949SDH3
Hello David,
Thank you for your question We have done an investigation into your model MDB4949SDH3, we have discovered that the Control Panel would be the part that has the parts you are referring to as part of it. It is available under part number PS11769412. We hope this helps you.
Cycle starts for one minute then goes to cancel and drains
For model number MDB4949SDH3
Hi Gill,
Thank you for your question. If your dishwasher stops mid-cycle, there are some parts that you will need to check to see which one is causing the issue. You will need to check the door latch, the electronic control board, the control panel, and the heating element. We have included a link from our website that you may reference on how to check these parts. Once you have determined the part you need, please call customer service. We look forward to hearing from you!
Leaking profusley when cycle 1st starts. Water flowing from
Bottom of drain pump and possibly higher. Replaced drain pump and verified drain hose ok. Didnt correct. Other possibilities?
For model number MDB4949SDH3
Hi Stan, thank you for contacting us. Based on the description that you have provided, we would recommend checking the water inlet valve, part number PS11752927, to fix the issue. It is located behind the lower kick plate panel in either the right or left corner. We have included a relevant video for you to help you with the process. We hope this sorts out your problem!
The dishwasher display flashed “1200” for a long time. Now it only shows a red lock symbol. It does not response to any buttons being pushed.
For model number MDB4949SDH3
Hi Glen, thank you for your inquiry. Based on our research, the 1200 indicates the remaining cycle time. Red lock symbol indicates that the control lock is activated. The control lock avoids unintended use of dishwasher between cycles. All buttons are the disabled. To unlock the control, press and hold sanitize for 3 seconds. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i
... Read morenput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
