This suspension spring is 7 inches in length, and is sold individually. It is a good idea to replace all six springs at once to maintain the same tension level. To complete this repair you will need a...
This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is ac...
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome ass...
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race was...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This is a replacement lid switch actuating cam for your washer. The cam is located on the underside of the washer lid, near the hinge. The cam actuates the lid switch, so your washer knows the lid is ...
This kit includes the lid switch and the plunger. The pin on the lid pushes on the lever of the switch to tell the machine that the lid is closed.
$57.33
In Stock
Questions And Answers for MAV6000AWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carol
September 29, 2021
What part needs to be or place a part when washers quits spinning water out of cloths
For model number MAV6000AWW
Hello Carol, thank you for writing. The likely cause for this issue is a clogged or faulty Drain Pump with Pulley PartSelect Number PS11741799. We have attached a video for you to view for installation information. Good luck with your repair.
Quand j'essore ma laveuse fait des bruits comme des pièce de ferraille qui se frotte ensemble
For model number MAV6000AWW
Bonjour Carole, Merci pour la question. Nous suggérons de vérifier l'usure ou les dommages de l'ensemble de roulement inférieur. Si vous avez besoin d'aide pour passer une commande, le service client est ouvert 7 jours sur 7. N'hésitez pas à nous appeler. Nous avons hâte d'avoir de tes nouvelles!
Hi: My Maytag washer works well on warm or hot. It goes through whole cycle. If you select warm and cold rinse it will not fill on cold rinse, just a small trickle. If select cold wash and cold rise, it will not fill, again just a small trickle. Thanks for your help Dave W
For model number MAV6000AWW
Hi David, thank you for the great question. Our research shows that the issue is either the Analog Water Temperature Control Board part number PS11739474 or the Water Inlet Valve part number PS11739377. We hope this helps.
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the
... Read morecomplete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do.