Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This suspension spring is 7 inches in length, and is sold individually. It is a good idea to replace all six springs at once to maintain the same tension level. To complete this repair you will need a...
This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is ac...
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome ass...
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race was...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
Hoses are the most likely cause of clothes washer leaks. This tub-to-pump hose carries the water from the tub to the drain pump. If you notice that your tub is leaking during the wash cycle, check the...
$34.97
In Stock
Order now and your part arrives by Mar 23
Questions And Answers for MAV6000AWQ
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Peggy
September 18, 2023
What is the black round rubber piece that was with the lid lock assembly when i removed it? It came off on the inside where the lid hits the plunger. Its round and looks like it should go over something. I cant figure out how to put it back.
Thanks
For model number MAV6000AWQ
Hi Peggy, thank you for getting in touch. According to our research, the black piece that you are referring to comes as a part of the lid switch assembly, part number PS2003435. You may need to make sure the lid switch assembly is not broken. If it is broken, you may need to replace it. Let us know if you have further questions!
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the
... Read morecomplete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do.
