This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these belts has worn or stret...
$41.25
In Stock
Order within the next 11 hrs and your part ships today!
This kit comes with a hub assembly, agitator seal, and spanner nut. If your washer leaks once it is full (with or without clothes in it) or leaks during agitation, then you should replace the seal. Th...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.76
In Stock
Order within the next 11 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Order within the next 11 hrs and your part ships today!
This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.
$200.68
In Stock
Order within the next 11 hrs and your part ships today!
The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is ju...
$15.28
In Stock
Order within the next 11 hrs and your part ships today!
This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Ma...
$11.14
In Stock
Order within the next 11 hrs and your part ships today!
This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time. The tub bearing kit fixes issues with leaking, loud noise, excessive shaking/moving or if your pump is no...
$55.59
In Stock
Order within the next 11 hrs and your part ships today!
This lid switch check is used in washers to detect if the washer lid is open or closed. This prevents a cycle from spinning when the lid is still open and is also used to start your washer once a cert...
$48.41
In Stock
Order within the next 11 hrs and your part ships today!
This black lid switch assembly comes complete with a bracket, two switches, and a fuse. An open fuse might indicate that the lid switch is bad. The point of the lid switch is for the tub to stop spin...
$42.42
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for MAT10CSAAW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rob
March 8, 2022
I have an unbalanced load light on but washing machine is completely empty. I have unplugged the unit to reset it but when I plug it back in the light comes back on. I can’t find any damaged parts causing the off balance and machine is level. What can I do to clear the unbalanced load light?
For model number MAT10CSAAW
Hi Rob,
Thank you for your question. If the unbalanced light is on when the washer is not in use, the washer may not be level and you will to adjust the leveling legs. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel. I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools
... Read moreand about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag wa
... Read moreshers, when I came across your site. By looking at your diagrams, I determined what parts I needed and ordered them. The parts arrived in 2 days, and I installed them. There were no leaks and it cost me under $70 (a repairman would have cost at least $250). The only thing I would recommend to those in similar situations, is to purchase a spanner wrench (your site does not sell, but others do). The stem seal and hub assembly is reverse threaded (clockwise to loosen) and is difficult to remove due to tight quarters in the tub.
1: Disconnected all water and electrical connections. 2: Removed front panel. 3: Disconnected all wires leading from the control panel and removed the top of the washer. 4: Removed the springs that holds the drum down on the damper pads. 5: Flipped washer upside-down so the drum would hang from the bottom of the wash.
... Read more This made it easy to clean the area since it was full of dirt and ground metal dust. 6: Glued new pads (per the instructions) to the cone that protrudes up from the bottom of the washer and allowed to dry. 7: Lubricated the pads with the provided grease and added additional silicon grease to insure smooth operation. 8: Replaced drive belt. 9: Flipped the washer back up-right and installed the drum springs. 10: Reconnected all wires and attached the top of the washer. 11: Reconnected all electrical and water lines and tested operation. 12: Replaced the front panel.
Washer now runs as quite and smooth as it did when it was new.
