This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your wa...
$4.39
In Stock
Order within the next 11 hrs and your part ships today!
This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heate...
$27.97
In Stock
Order within the next 11 hrs and your part ships today!
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft....
$27.87
In Stock
Order within the next 11 hrs and your part ships today!
The thermal cut-off (Dryer Thermal Cut-Off Fuse Kit, Dryer Thermal Cut-Off Kit) prevents the dryer from overheating when the dryer high limit thermostat fails in a closed circuit condition. This part ...
$36.58
In Stock
Order within the next 11 hrs and your part ships today!
This part replaces your appliances latch (Door Latch Kit, Door Catch, Dryer Door Latch Kit). On your appliance you will find both a strike and a catch. The strike is mounted on the body of the dryer, ...
$5.04
In Stock
Order within the next 11 hrs and your part ships today!
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
$8.00
In Stock
Order within the next 11 hrs and your part ships today!
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
$26.95
In Stock
Order within the next 11 hrs and your part ships today!
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There...
$35.28
In Stock
Order within the next 11 hrs and your part ships today!
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
$22.69
In Stock
Order within the next 11 hrs and your part ships today!
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining ...
$27.58
In Stock
Order within the next 11 hrs and your part ships today!
This dryer drum belt from Whirlpool/Kenmore has five ridges. It is used for many of Whirlpool's brands of clothes dryers. This flat belt is 1/4 of an inch wide.
$21.95
In Stock
Order within the next 11 hrs and your part ships today!
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$13.42
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for LTE6234DQ2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dolores
January 19, 2020
Dryer is running but clothes come out very damp. No hot air cones out to dry clothers
For model number LTE6234DQ2
thank you for your question. Looking at your model information there are a few parts that you should take out and test to see which one is giving you the issue. The first parts to check in this case would be all of your thermostats and thermal fuses. You can test those parts with a multi meter and they should be reading 0 ohms to be working correctly. If those parts are fine, you should then go on to testing your heating element as well. You can also test that with a multi meter and it should be reading between 0 - 50 ohms. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Glenn
February 17, 2020
The dryers starts and runs for a few seconds then stops.
For model number LTE6234DQ2
Hello and thank you for writing.
It certainly sounds like it could be a faulty cycling thermostat PS11741405 and/or possibly a faulty door catch PS334230you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
I have replaced both the thermal cut off and thermostat fuses (pn 3390291 & pn 3977394)
As well as the dryer control timer (pn 3976569). When i select timed drying 60 and push the start button, the dryer runs for 9 seconds then stops. If i wait 5 minutes or so, rotate the dial to any other setting, it does the same, runs for 9 seconds and shuts off. Is there another cause for this other than what i have already changed out?
For model number LTE6234DQ2
Hi Glenn,
Thank you for your question. If you have replaced these parts and the dryer is still shutting off too soon, there are some other parts that you will need to check to see which one is causing the issue. You will need to check the timer, the door switch and the start switch. You should also check the dryer vent to see if it is clogged with lint. If it is, you will need to clean it as it can cause the dryer to shut off prematurely. We hope this helps. Thank you and have a great day.
Was this helpful?
Thank you for voting!
Brad
December 23, 2021
What is the part number for the transmission for the whirlpool ltg6234dg0 parts
For model number LTE6234DQ2
Hello Brad, thank you for writing. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS341974. We have an installation video for you to access. We hope to hear from you soon.
Hi Lou,
Thank you for your question. If the dryer is too hot, there are some parts that you will need to check to see which one is causing the issue. Here is a link from our website that you may reference on what parts to check, https://www.partselect.com/Repair/Dryer/Too-Hot/. I hope this helps. Thank you and have a great day!
The job looked intimidating but turned out to be very easy. First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum
... Read morep. The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed. One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary. Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs. Slip the new cogs into the underside of the cup, and slide the cup back down in the a
... Read moregitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out). Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back
... Read more off.
