This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft....
This part replaces your appliances latch (Door Latch Kit, Door Catch, Dryer Door Latch Kit). On your appliance you will find both a strike and a catch. The strike is mounted on the body of the dryer, ...
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is ...
The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings, and one palnut (or retaining washer). The kit does n...
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There...
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining ...
This part provides the tension required for a multi-ribbed belt. It also helps the belt rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long t...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front...
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
$11.06
In Stock
Questions And Answers for LTE5243DQ6
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pat
February 4, 2024
My washer leaked all over the floor during the drain cycle on the last run. Assume it’s the drain pump so trying to find instructions on how to open the panels and verify before I order.
For model number LTE5243DQ6
Hi Pat, thank you for contacting us. We have provided some relevant instructions which may not be of the exact same model but will help while removing the panels to verify whether the drain pump is faulty or not. You just need to un-thread the screws securing the lower access panel. Detach the panel and set it aside. Remove the two rear access panel clips. Detach the spring clips securing the washer's top panel and lid. Pull the top panel forward, then lift up. Un-thread the screw to release the support bar from the front panel. Un-thread the screws securing the front panel to the side panels. Lift the front panel up. You will have access to the drain pump. Carefully examine the drain pump, part number PS11741239. If it is faulty, we would recommend replacing it to fix the issue. Glad to be of help!
I have a Whirlpool thin twin model ltes243dq6 that is overflowing i have replaced the water inlet valve and it did not fix the problem. I thought perhaps it could be the water pressure valve. Have you got any diy videos or perhaps a service manual i might download? Of course will perchase parts from your company.
For model number LTE5243DQ6
Hello James,
Thank you for your question. Our sources don't show there being a water pressure valve other then the water inlet valve, however if replacing the valve did not solve the overflowing issues, we suggest checking the water pressure switch under part PS11741236 for your model to fix the overflowing issues. We do not have an installation video for this particular part, but both instructions and your models manual can easily be found searching online on other sources. We hope this helps.
I like to know if you have door switch for the washer for above model
For model number LTE5243DQ6
Hello Abdulaziz, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11741702. We hope this helps!
Hello,
I have a stackable washer/ dryer. The dryer is not turning on at all. Can I just purchase the dryer since the washer still works well?
For model number LTE5243DQ6
Hello Monica, thank you for reaching out. According to our research, your model is stacked and you can not replace the dryer. We would recommend checking the timer, part number PS11741710, to solve the problem. Glad to be of assistance!
Hi Lori, thank you for the question. Based on our research, your model was manufactured approximately in 2003. For us to locate the correct age, we will require the serial number of your model. We hope that helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
The job looked intimidating but turned out to be very easy. First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum
... Read morep. The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed. One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary. Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary a
... Read moreccess to the pump. Once the machine is on it's back you remove the hose clamps with a pair of pliers and disconnect the hoses. The pump is secured to the motor with a pair of spring steel retaining clips which are easily popped off by hand. Once the clips are removed, the pump is in your hand. Put the new pump in place, replace the retaining clips and hoses, and you're done. This has to have been the easiest repair I've ever done. I wish cleaning gutters was this easy.