Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The upper dishrack is used to hold your dishes in place while the dishwasher goes through the wash cycles. Over time the dishrack can become damaged, start to rust, or be missing rollers, and the dish...
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the baske...
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, ...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
This dishwasher door latch assembly is a critical component designed to ensure safe and efficient operation. It features an integrated switch that functions as an on-off mechanism, preventing the appl...
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete i...
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plasti...
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kaylee
December 20, 2019
Buttons on dish washer not working. First the lights were flashing, now the only light working is the lock button.
For model number LFID2426TF0A
Hello Kaylee, thank you for your question. We would recommend testing the LATCH ASSEMBLY
Part Number: 5304516818, heater PartSelect Number: PS3653449, High Limit Thermostat
PartSelect Number: PS2331123 and Turbidity Sensor PartSelect Number: PS2363559 first. If these parts are tested/replaced and the issue persists, we would recommend testing the control board and control panel. I hope this helps!
1 person found this helpful.
Did this question help you?
Thank you for voting!
Irene
January 3, 2020
The door does not apprear to be latching. Also the sensor pad keys light up when power put back on but goes into child lock mode and cannot select wash or start. Is the lock being bad affect the touch bad? Or are both on the fritz. Tried new control panel but did not fix
For model number LFID2426TF0A
Hello Irene,
Thank you for your question. Our sources suggest replacing the door latch assembly under part PS12585469 for your model to fix the issues. We hope this helps!
Why do all the lights flash on the dishwasher and it will not start. I already tried resetting the breaker and checked the latch for continuity.
For model number LFID2426TF0A
Hello, Thank you for your question. If the latch is working you will need to check the connection between the board and the panel. Those are usually the other cause of a unit not starting. We hope this helps.
Did this question help you?
Thank you for voting!
Maria
January 5, 2022
I only purchased this awhile ago. I want to order a part for my dishwasher, the spray arm fell off and melted.
For model number LFID2426TF0A
Hello Maria, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Part #: PS11770509 for the Lowe Spray Arm and Part #: PS11770527 for the Center Spray Arm. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
The hardest part was disconnecting the dishwasher. the motor is located on the bottom so after pulling it out and laying it down on the front of the machine the motor unplugs and 2 screws hold it in place.The new motor comes with "O" rings so I applied a little grease and put it back together. 2 minutes to replace motor, 15 minutes to dis
... Read moreconnect water and electric, 15 to reconnect.
