Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This part replaces your appliances latch (Door Latch Kit, Door Catch, Dryer Door Latch Kit). On your appliance you will find both a strike and a catch. The strike is mounted on the body of the dryer, ...
The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings, and one palnut (or retaining washer). The kit does n...
This part provides the tension required for a multi-ribbed belt. It also helps the belt rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long t...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This lint filter helps keep your dryer running safely and efficiently by catching lint and fibers from clothes. It has a unique kidney shape and fits securely with four metal clips. Made from strong s...
This push-to-start switch activates the dryer when the button is pressed and released. If your switch is not turning on or off, will not start, or the contacts inside the switch are shorted out, it is...
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint c...
Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 de...
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Terry
January 24, 2020
I have, in the past, removed the back panel so I could remove lint. I cannot seem to get it all out so now I would like to remove even more of the housings but cannot seem to locate the correct parts to take off. I need to get behind the screen (part number: Ps347545) somehow. I really would like to get all the lint out of the back but need to break it down even more. Can you advise?
For model number LDR3822PQ1
Hello and thank you for writing.
Here are a few steps you can follow that should clear the lint from the dryer:
Step 1
Unplug the Whirlpool Duet dryer's power cord from the dryer outlet. Open the dryer door and pull out the lint trap from inside the door. Set aside.
Step 2
Insert a dryer lint brush into the lint-trap cavity of the dryer. Slide the lint brush from side to side inside the cavity, then pull out the brush and lint. Remove lint from the lint trap and insert it back into the dryer. Close the dryer door.
Step 3
Remove the two screws securing the lower front panel to the Duet dryer by using a Phillips-head screwdriver. The screws are under the bottom ledge of the lower-front panel. Pull the panel away and set aside.
Step 4
Brush out as much of the lint as possible from the inside of the cabinet using the dryer lint brush. Use care when brushing around wires and their connections.
Step 5
Attach an upholstery brush to your vacuum cleaner and vacuum the remaining lint from inside the cabinet. Again, use care around wires and their connections.
Step 6
Position the lower-front panel back onto the dryer and secure it with the screws. Plug your Duet dryer's power cord back into the outlet.
We hope this helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Did this question help you?
Thank you for voting!
Jeffrey
November 1, 2021
My basement got water in it got my dryer wet now it won"t start
For model number LDR3822PQ1
Hello Jeffrey, Thank you for the question. There would be more then one part to check if it was flooded. You would need to test any electrical part with a multi meter to check on continuity. You would need to check wiring, motor and controls. Anything with electricity. We hope this helps!
1 person found this helpful.
Did this question help you?
Thank you for voting!
Sandie
January 30, 2025
The dryer isn't heating up very much. I wonder if I need to replace the heating element. Can you tell what part i need and how to replace it
For model number LDR3822PQ1
Hi Sadie, Thank you for writing. We suggest testing the Thermostat to check continuity. It is located on the Heating element so you will need to open up the cabinet to access the Thermostat. We hope this helps!
I broke the knob off and need the knob and the switch. Push to start bottom and switch
For model number LDR3822PQ1
Hi Shannon, thank you for contacting us. The compatible push-to-start knob and push-to-start switch for your model are PS11746347 and PS11742178. If you need help placing an order, customer service is open 7 days a week!
Hello, my dryer is making a rhythmic thumping/banging noise, about 1 beat per second, a bit like a metal sound. Any idea on what this could be? It is drying fine and otherwise working well. Appreciate any help, thank you.
For model number LDR3822PQ1
Hello Fran, thank you for getting in touch. Based on our understanding of the issue, we would suggest checking the idler pulley, part number PS11743765, to solve the problem. Glad to be of help!
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
You open up the lint filter access door and remove the two small screws that hold it to the top of the dryer. Once they are removed, you insert a flat blade screwdriver under front-top of the unit and the top will pop off. Exerting a little pressure towards you will help lift to top off the mounts. There are no other screws to remove.
... Read more The new switch comes attached to a clip. You just pull off the old clip and replace it with the new one and discard the old switch.
I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!
