My Orders
KGCD807XSS01 KitchenAid Cooktop - Overview
Diagrams for KGCD807XSS01
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$30.53
In Stock
Burner Electrode
Part #WP74009336
This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replace...Read morement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.
Read less
$6.40
In Stock
$21.45
In Stock
Screw
Part #W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
$7.47
In Stock
$9.62
In Stock
$7.47
In Stock
$81.73
In Stock
X-Large Burner Head with Electrode
Part #74007736
This is the burner head and electrode for your gas range. If your gas igniter glows but will not light, or if the element will not start or heat entirely, you may need to replace the burner head. This burner head is approximately 4¼ inches in diameter and is sold individually. Please note that the mounting screws for this burner head are ...Read moresold separately. To replace the burner head, simply unscrew the old, defective burner head and screw in the new one.
Read less
$74.98
In Stock
$27.36
In Stock
Burner Control Knob
Part #WPW10301588
Sold individually. This knob is used to controls the heat of the surface burner on your range.
$25.75
On Order
Fan Control Knob - Chrome
Part #WPW10303835
NOTE: This knob control the fan not the burner. Sold individually.
$9.62
In Stock
$94.66
On Order
Range Exhaust Vent Blower Wheel
Part #WPY707985
This blower wheel attaches to the ventilation motor to draw in and exhaust smoke, steam, and cooking vapors, helping maintain clean airflow in your kitchen. Built from durable metal for heat resistance and long-lasting performance, it measures approximately 7 inches in diameter and under 4 inches deep for a secure, efficient fit. Designed...Read more to spin smoothly on the motor shaft, replacing a worn or damaged blower wheel can restore proper airflow, reduce noise, and ensure reliable ventilation performance.
Read less
Manuals & Care Guides for KGCD807XSS01
Click to downloadInstall
Installation Instructions
(2.39MB)
Install
Installation Instructions
(3.06MB)
Manual
Owner's Manuals
(1.77MB)
Manual
Owner's Manuals
(2.55MB)
Specs
Product Specifications Sheet
(0.73MB)
Common Symptoms of the KGCD807XSS01
How this model fails, and the parts that fix it.
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ignitor did not work
24 of 25 people
found this instruction helpful.
- Removed the cover.
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a hi ... Read more gh temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works.
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a hi ... Read more gh temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!