KECO376MCS KitchenAid Microwave - Overview
Sections of the KECO376MCS
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Range Surface Burner Knob
PartSelect #: PS11740686
Manufacturer #: WP307458
This knob is sold individually.
$20.95
In Stock
Heat Resistant Adhesive
PartSelect #: PS11728058
Manufacturer #: W10841140
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising th...
$17.80
In Stock
Thermal Fuse
PartSelect #: PS11740687
Manufacturer #: WP307473
This thermal fuse is mounted on either the heating element or burner tube housing.
$51.97
In Stock
Knob Bezel
PartSelect #: PS12348924
Manufacturer #: W11194997
This Whirlpool BEZEL-KNOB is a genuine OEM part compatible with various models of the same brand. Designed for ranges, it functions as the surface burner knob bezel. This vital component attaches behi...
$51.45
In Stock
Questions And Answers for KECO376MCS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the KECO376MCS
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer stopped working
From previous experience I suspected the thermal fuse. Turned off the power and removed the front of the dryer by removing the two philips head screws in the door hinge and the two screws on the opposite side of the opening. The front came off easily since all that holds it in place besides the 4 screws are two spring clips. The ther
... Read more
mal fuse is located on the side of the chamber enclosing the heating element. I removed the wires connected to the thermal fuse and temporarily joined them together with a spade type connector in order to determine if the thermal fuse was the problem. Turned the power back on and tried the dryer......it ran normally. Turned the power back off and removed the thermal fuse by taking out th two screws with a 1/4" nutdriver.
Ordered a replacement thermal fuse, installed it (with power turned off) and put everything back together. Dryer functioned normally after the thermal fuse had been replaced.
The thermal fuse can be removed and reinstalled using a 1/4" nutdriver. The wires are connected with push on spade type terminals.
Note: The swing damper on the dryer vent (the hooded cover where it exhausts to the outdoors) was jammed in the closed position with an accumulation of lint, which caused the dryer to overheat and blow the thermal fuse. If you experience a blown thermal fuse, always look for the cause or you'll blow the replacement within minutes of running the fryer again.
Ordered a replacement thermal fuse, installed it (with power turned off) and put everything back together. Dryer functioned normally after the thermal fuse had been replaced.
The thermal fuse can be removed and reinstalled using a 1/4" nutdriver. The wires are connected with push on spade type terminals.
Note: The swing damper on the dryer vent (the hooded cover where it exhausts to the outdoors) was jammed in the closed position with an accumulation of lint, which caused the dryer to overheat and blow the thermal fuse. If you experience a blown thermal fuse, always look for the cause or you'll blow the replacement within minutes of running the fryer again.
Read less
Parts Used:
-
Mary Ann from East China Township, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
27 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not turn start
I troubleshot the repair using the repair help section from Parts Select. It made finding the problem a snap. I then removed the four wires and two screws that held the heating element in place. Removed two screws that held thermal fuse in place and replaced. By accomplishing the repair myself I saved well over a hundred dollars.
Parts Used:
-
John from Midway, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken knobs
I removed the existing knobs and popped the new ones into their place! It was aggravating that I could not find a local source to purchase replacement knobs, so I was very glad to discover PartSelect. Instead of a $1000 replacement cooktop, I replaced the knobs for less than a tenth the cost.
Parts Used:
-
Louise from Austin, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!