This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible wi...
The function of the oven sensor is to detect the temperature within the oven cavity. If you notice that the oven is too hot or too cold, or it is not heating evenly, you may need to replace the oven s...
This part is the replacement oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover is rigid and protects the oven light bulb from being damaged. The main ...
The light housing is also known as a lamp holder and is a part for the oven in your range. The function of this piece is to hold the bulb that will light up the inside of your oven. As per the manufac...
This part is a replacement screw for your oven. It is made of black metal and is sold individually. This screw is approximately 1/4 inch in diameter and about 1/2 inch in length. It is designed to con...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Charles
April 9, 2024
LOC is ON. Door is NOT LOCKED but control selections do not respond.
For model number JTP70SP1SS
Hi Charles, thank you for reaching out. Based on our research, your control lock is activated. To unlock, press 9 and 0 key at the same time for 3 seconds until the display show LOC OFF. We hope that helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tom
February 26, 2020
Oven cut off after 5 hours running. Clock works time works and clear clicks but nothing else will work. The lock screen does not work ( 9 0 ) i think its the thermostat but i am not sure.
For model number JTP70SP1SS
Hi Tom, thank you for your question. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. Good luck with your repair.
Was this helpful?
Thank you for voting!
Robert
February 28, 2023
How to replace bake element
For model number JTP70SP1SS
Hi Robert, thank you for contacting us. Firstly, shut off the power supply. Then open the oven door and remove the racks from the oven. Locate the bake element at the bottom and take a screwdriver to unthread the mounting screws attached to the bake element terminals. Disconnect the two wires and remove the bake element, and install a new one. We hope this information is useful!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wal
... Read morel. Overall, a very easy repair once you get the oven out.
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.
Removed the oven door for easy acces to oven. Unscrewed (philips screwdriver) the screw holding temp sensor in place. Gently pulled the wiring until quick connector was located. Pushed down on locking level on quick connect while holding other end of wiring (so wiring would not fall back behind oven). Connected the new sensor and scre
... Read morewed back in place. Reinstalled oven door. Tested temperature settings by turning on oven and comparing with a separate oven thermometer.