Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane.
This valve automatically cuts off the flow of gas at a certain pressure.
Elevate your cooking experience with the GE Spark Module Kit. This must-have component is designed to efficiently control the sparks for lighting your cooktop surface burners, ensuring a consistent an...
First I shut off the gas valve below the range and unplugged the unit from the electrical outlet. I left the flexible gas line fitting undisturbed/attached to the range top gas fitting. Then I removed the two screws below the unit (under the counter) that affix the range to the counter/support structure. Then I removed all of the knobs
... Read moreand burner grills and gas diffusers sitting on the top of the range. Then I lifted out the burner bowls and disconnected each from their respective spark wires. Then I gently pried the range from its hole in the counter being carefulm not to break the glass top and lifted it out turned it at an angle to the counter top hole and set it back down on the counter. Then I gently pried off the glass top from the metal range base, cleaned it thoroughly and set it aside. Then, I placed the new spark module next to the old one and one by one I transferred each wire to its respective location on the new module. The instructions pointed out that the new spark module has a revised grounding scheme and that a ground wire is no longer needed, so I removed and discarded the green ground wire. I then affixed the new spark module into the location where the old spark module had been. Next I replaced the wiring harness which contains the switches for each burner location. It is important to replace the wiring harness along with the spark module as they must work together reliably to complete the gas ignition circuit. The old wiring harness simply lifts/unsnaps out and the new one snaps into its place. Once both the spark module and wiring harness were in place, reassembly of the range was simply the reverse of disassembly.
I had a 14 yr. old GE cook top. Back right burner out, igniter blew circuit breaker (I had disabled this burner many months prior to use other four burners). Cause by dripping into on/off knobs into switch. TO FIX: I looked online for answers, I ordered the wire harness, Un-plug the stove, turn off inline Gas, take off all knobs and
... Read more loose items. Open up stove-top, (taking off two Phillips screws on each burner plate). Now replace the wire harness from the line voltage to each burner. The new wire was much different (improved) but it would only fit one way (after a bit of panic). I un-plugged the old wire harness one by one, plugged in the new cord one by one (same locations, colors), Lift up each old burner switch (one by one) and Install newly wired Switches over top of each burner (at a bit of an angle to seat properly 22deg?). Now the hard part, Clean all the stove, every part. Put it back together. Try it out. stand back.....just kidding. I called into site and GE help line. I finally got a help desk. Very nice and helpful to ensure me that this part was correct part# for this stove. No I did not take any pictures. Old-fashioned. Note: I ran all parts through dishwasher. This needs to unplug and remove each igniter also.
The OEM harness goes around counter-clockwise starting from the top right knob (after attaching to the cooktop power). This replacement unit will not fit in this order. It will only fit starting at the bottom right knob, move to top right knob, then proceed counter-clockwise.
