JD630SF3SS General Electric Range - Instructions

I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out.

removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.

Removed the oven door for easy acces to oven. Unscrewed (philips screwdriver) the screw holding temp sensor in place. Gently pulled the wiring until quick connector was located. Pushed down on locking level on quick connect while holding other end of wiring (so wiring would not fall back behind oven). Connected the new sensor and screwed back in place. Reinstalled oven door. Tested temperature settings by turning on oven and comparing with a separate oven thermometer.

The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.

Ordered window pack from PartSelect then removed oven door from front of stove, then removed back of door and silver backing and glass pack. Dropped new glass into place. Replaced all backing,put door back onto stove. Tip. When removing screw keep them separated from each other as not to get mixed up when putting everything together. Good Luck, PartSelect has all the parts you need, this my second getting a part from them.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

After reviewing the potential causes for the error code, I decided I'd try to change out the temp sensor. Using the ohmeter, I saw the difference immediately between the old and new sensor. The sensor is accessed from the back of the stove, and must be slide out to gain access to the rear panel. Since the stove I have is a built in, removing the stove and the access panel was the hardest part of this repair. Resetting the glass control panel was also a bit tricky to calibrate the touch sensitive buttons. Good luck.

Took off the knobs and retainer nuts. Carefully setting them on top in the same order as they came off. Unscrewed the bottom retainer screws. Removed the main control trim. Unscrewed the top retainer screws. Carefully pulled the broken control assembly panel out of the wire harness. Reversed the procedure to install the new Panel.
Found the part quick and easily on your site and had it shipped next day. Wonderful Experience!

lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

First; turn off breaker to stove.
Second; remove two Phillips head screws that hold the top on, located in front, underneath, will have to open the oven door to see.
Third; prop the top up.
Four; disconnect wire clips of old element.
Five; plug in new wire clips of new element.
Six; unprop the top and realign the top.
Seven; replace the two Phillips head screws to secure the top, then close oven door.
Eight; turn breaker back on.
Done and Back in Action! You Can Do This!

Disconnected breaker. Removed knobs, plastic retaining nuts mounted to each switch shaft. Removed four 1/4 inch hex head screws on front panel and two screws securing defective switch. Removed bad switch, and replaced with new part. Took photo of wiring before removing old part. Referred to photo to ensure correct wiring of new part. Reassembled front panel in reverse order of disassembly. Turned breaker to on, and tested new switch. All worked well.

Unplug stove.2 screws out ,lift top ,disconnect bad element, connect new element, put top down .2 screws in .plug stove back in...EASY PEASY

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.