Models
>
JCP346BM3BB
JCP346BM3BB General Electric Cooktop - Overview
Sections of the JCP346BM3BB
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Infinite Control Switch
PartSelect #: PS1016429
Manufacturer #: WB24T10119
This part is sold individually and is for ranges. The control switch turns the surface element on and off and determines the temperature of the element. This will need to be changed if the control swi...
$91.57
In Stock
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.22
In Stock
Knob
PartSelect #: PS1480778
Manufacturer #: WB03T10270
This is a replacement burner knob for your range. It is made of black plastic and is approximately 2 inches in diameter. The knob allows you to turn on and adjust the heat level of the range. If the k...
$12.23
Special Order
Radiant Surface Element - 11 Inch
PartSelect #: PS2370249
Manufacturer #: WB30T10146
This part is mounted on the bottom of a ceramic glass cooktop and provides heat for that area of the cooktop.
$184.45
In Stock
Switch Seal
PartSelect #: PS243590
Manufacturer #: WB2X9504
This part goes between the infinite switch (under the cooktop) and the knob.
$32.19
In Stock
Tape
PartSelect #: PS227306
Manufacturer #: WB06T10007
This roll contains 108 inches of tape.
$50.81
In Stock
Questions And Answers for JCP346BM3BB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JCP346BM3BB
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Switch failed
I turned off the circuit breaker and tested the cook top. I pulled the cook top out and laid a piece of plywood over the opening to work on the cook top and not scratch the granite counter top. The mistake I made was to turn the cook top upside down and separate the top from the housing. The dampening springs came off the burners and I
... Read more
could have damaged the elements (but they checked out ok). I turned the whole assembly right side up again and replaced the switch and put it all back together. It works great...thank you for the part.
Read less
Parts Used:
-
John from Fresno, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
34 of 48 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electric range burner not working due to control switch
Turned off power to counter top range and pulled-up from counter. Set range on counter and removed 16 screws from around the housing allowing me to pull-up and remove range top. Used socket to remove 4 screws holding control switch bracket in place and 2 screws holding bad switch in place. Disconnect wires from bad switch and reconnected
... Read more
to new switch. Placed and screwed switch bracket back in place. Before placing range top back I turned power back on to to test burner operation. Burner and switch operated correctly and I completed screwing range top back in place, setting back down into counter top. Done
Read less
Parts Used:
-
Rodney from Erath, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
21 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
RF Dual Burner out. Smoke in the area of controls
Shut off circuit breaker. Removed cooktop from island counter. Removed all knobs. Removed all screws after finding layout diagrams of unit on your web site. Lifted glass top from metal cabinet. Ordered control after trouble shooting the problem. (Master Electrician). Obviously burned out from water in control. Ordered control on line and
... Read more
installed it when it arrived three days later. Before installing control I cleaned and dried out the area. I cleaned the glass top around all the control shaft holes and the rubber boots and lubricated them with silicone to help keep them dry and for ease of turning controls. Turned on circuit breaker and checked all burners, pilot light and hot top indicating lights.
Read less
Parts Used:
-
Al from Ocala, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
12 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!