Models
>
JCP340WJ1WW
JCP340WJ1WW General Electric Cooktop - Overview
Sections of the JCP340WJ1WW
[Viewing 1 of 1]
Manuals & Care Guides for JCP340WJ1WW
Click to downloadKeep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.22
In Stock
Large Haliant Burner with Limiter - 8"
PartSelect #: PS243903
Manufacturer #: WB30T10045
This haliant burner element is a gneuine OEM replacement part for your stove. This element is 8 inches in diameter. The element lies underneath the stovetop, and will need to be replaced if it stops h...
$148.32
In Stock
Foam Rubber Tape
PartSelect #: PS11726663
Manufacturer #: WB02X26088
This is foam tape and it is usually used in conjunction with your range, specifically on the cooktop. Its purpose is to help seal the edges of the cook top to the counter top. Another of its functions...
$39.82
In Stock
Switch Seal
PartSelect #: PS243590
Manufacturer #: WB2X9504
This part goes between the infinite switch (under the cooktop) and the knob.
$32.19
In Stock
Tape
PartSelect #: PS227306
Manufacturer #: WB06T10007
This roll contains 108 inches of tape.
$50.81
In Stock
Cerama Bright Cooktop Cleaner
PartSelect #: PS783497
Manufacturer #: PM10X310
This is a 28 oz bottle of Cooktop Cleaner.
$18.28
In Stock
Surface Burner Switch - 6 Inch- 1200W
PartSelect #: PS236391
Manufacturer #: WB23M8
$136.48
In Stock
Questions And Answers for JCP340WJ1WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JCP340WJ1WW
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Large burner would not get hot
Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!
Parts Used:
-
Kevin from Leominster, MA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
70 of 92 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left rear element would not get hot.
FIRST TURN OFF THE CIRCUIT BREAKERS THAT POWER THE COOKTOP!! Remove the cooktop from the counter by removing the screws from the mounting straps under the counter. Then remove the screws that hold the glass cooktop to the frame and lift off the glass top. Next lift up the bad element and unplug one wire from the bad element and plug it in
... Read more
to the new element. Make sure to put it on the exact same terminal of the new element. Do this for all the wires. Remove the two mounting tabs from the old element and put them on the new element. Turn on circuit breakers and your done.
Read less
Parts Used:
-
John from Hopewell Junction, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
19 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Intermitently the switch would stick on high.
Pulled unit from the counter top, removed all side screws holding the top on and set the top off. Removed switch mount section, Identified the terminal wire locations. I then removed the old switch and connected the wires per my diagram. Returned all screws, tested the burner for opeation and reset the cooktop back into the counter hol
... Read more
e and secured.
Read less
Parts Used:
-
Larry from Mattawa, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
14 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!