This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
This ice maker (Ice Maker Assembly, Refrigerator Ice Maker) produces ice cubes that are ejected into the storage bucket. It is located in the freezer section of your appliance, mounted on the freezer ...
This is the replacement water filter for your refrigerator. It is white in color with a red cap and is approximately 3 inches wide and 6 inches tall. The water filter reduces contaminants and improves... No Longer Available
This light bulb is a 120 volt, 25 watt incandescent appliance light bulb with a small base screw-in that fits in a variety of appliances such as microwaves, refrigerators, freezers, cooktops, or stove...
In addition to the solenoid (115V), this kit also comes with a door strike and an ice door assembly. Please be advised the spring and roll pin are not included with this kit.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light ...
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If you are noticing temperature issues with your refrigerator or freezer,...
This part assembly has 2 functions: The defrost heater keeps the cooling coils from frosting over and the thermostat senses that the heat near the cooling coils has reached the desired temperature.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gord
December 29, 2019
There is an odour emitting from the refrigerator. We have cleaned the refrigerator, freezer and rear compartment thoroughly, but cannot eliminate the odour. It seems to be entering the fridge through the internal vents. Is there an air filter somewhere that should be replaced?
For model number JCD2389GES
Hi Gord,
Thank you for your question. We are not showing an air filter listed for this model, but if there is a lingering odor in the refrigerator, it may be the water filter. You should replace it in the time frame indicated in your owner's manual. Make sure that odor producing foods are covered or wrapped so they do not emit odors throughout the refrigerator. Here is a link where you may view your owner's manual for more information, https://partselectcom.azureedge.net/assets/manuals/5283BEEDC0E8E86D3CF60FB2D2D0D0AC9C666272.pdf. We hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Gwendolyn
September 18, 2021
Black foot on bottom of refrigerator broken, can it be replaced
For model number JCD2389GES
Hello Gwendolyn, thank you for writing We have researched the model you have provided and have found the part you are looking for is Rear Roller Wheel PartSelect Number PS11743179. The Wheel Pin is PartSelect Number PS11743130. We hope this helps.
Ice maker quit working. Has water to door.
Could the water control valve be bad if the water still works in the door?
For model number JCD2389GES
Hello Jo, thank you for your question. We have researched your model and found that the issue is probably with the Double Inlet Water Valve, part number PS2060970. If that does not take care of the issue, then the problem is most likely to be related to the Ice Maker, part number PS2121513. If you require assistance to place an order, please contact customer service. We hope that helps!
Side by side jenn air freezer side filter light on. Replaced filter in fridge side, light still on. Is there a filter in the freezer side?
For model number JCD2389GES
Hello Tom, Thank you for the question. After changing the water filter, reset the status. Press and hold the "WATER FILTER" button for 3 seconds. When the system is reset, the water filter icon will return to its BLUE color and the words “Replace Filter” will disappear from the display. Hope this helps!
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release. Unplug appliance. Remove timer cover by hand pressure @ edge. Remove single attachment screw & bracket at lower front of icemaker. Disconnect wiring harness from socket @ rear of compartment. Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment. Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall. Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer. Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit. Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable. A good push of the new unit towards the snap-ins along with some upward force will get it stable. Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in. It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient. Dump the first couple of batches of cubes just to make sure you're free of any residue.
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: one of the three screws that hold the ice maker to the refrigerator wall is hidden behind the large (black) end of the ice maker and is difficult to access. Before trying to replace the ice maker, make sure you have the physical dexterity to remove that screw. Second problem: it is not apparent how to remove the wire harness that plugs into the ice maker assembly. BEFORE you can remove the wire harness, you MUST remove the large white cap that covers the black end of the ice maker assembly and then push in a retaining tab to release the wire harness. If you don't do this, the wire harness will not release. Other than those two problems, it was relatively easy to remove three screws, unplug the wire harness, transfer three small, metal parts from the old ice maker to the new, plug in the new wire harness, mount the ice maker assembly so that the water tube is in the proper position, and then re-install the three screws. The ice maker works fine now. (P.S. I was told by an expert that the real problem might be a malfunctioning fill valve. I would have replaced the fill valve if replacing the ice maker assembly had not fixed the problem.)
Removed the Hex head small screw at the middle back of the Back wall of the fridge above the top shelf. Removed the 2 small Hex Head screws that go into the of the Plastic cover upwards into the top roof of the fridge. I ended up with an extra screw so I dont know what I did... The hard part is pushing up on the two tabs, one on each side in the extreme back on the bottom of that white plastic cover. You have to pull the coverwhile releasing the tab (locks) by pushing UP. The Right side was easier, I got that side to release and drop down. But the left side took some pressure on the tab with a fat screwdriver. Then you have to kinda of Bend the cover to get it to slide out...
Then take out the 2 phillips screws above the light bulbs. the left side one is tricky, need long skinny driver.
Drop assembly down and on the back right is the ADP board. Mine was a bare board but the replacements are enclosed in white plastic that fit in place just fine.
Pry connector off of the board carefully and drop new plastic circuit board case in and replace.
Put a thermometer in a glass of water. unplug fridge for 10 minutes and then plug it in. Give it a few hours.. Everything seems fine. A steady 39 degrees with the Fridge control at a few ticks right of middle. I have no idea what it was before my troubles... But 36 - 41 seems to be what you need.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
Stay on this site
Go to Canadian site
