Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
JCB840SF3SS General Electric Refrigerator - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This door shelf is a replacement part for your refrigerator. It is very easy to install and requires no tools. Simply pull out the existing shelf bar and snap the new one into place, making sure the l...
This part is the door fixed shelf, also known as the door shelf bar, and it is built for your refrigerator. It allows food and beverages items to stay in the door shelf. It is made of white plastic. I...
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the sw...
This compression ring is meant to hold the evaporator fan motor in place in the freezer compartment of your refrigerator. This is is a genuine OEM part. The tools needed to complete this repair are a ...
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. This part has been updated by the manufacturer and may appear different t...
This defrost timer will cycle for 25 minutes after every six hours of run time. The timer itself is made of plastic, and its terminals are bent, the leads are internal, and the label is orange. If you...
The condenser fan blade assembly helps to regulate the temperature in your refrigerator or freezer. This fan assembly has 4 blades, but other fans may have 3 blades, so be sure to check the number of ...
This is the replacement hinge washer for your refrigerator. The hinge washer is mounted on the top of the door hinge pin, and supports the refrigerator door, allowing it to open and close easily. The ...
This is a replacement crisper drawer for your refrigerator. The drawer is approximately 17 inches long, 13 inches wide, and 9 inches tall. It is made of clear plastic and is sold individually. The cri...
$81.49
In Stock
Order now and your part arrives by May 11
Questions And Answers for JCB840SF3SS
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Walter
April 29, 2023
I got this model number from the warming drawer on my GE Oven. I am looking for replacement knobs for this GE model. Everywhere I have Googled it come up as a refrigerator and shows me refrigerator parts.
I unable to find my oven model which is indicated above. The oven was manufactured in Mexico. Thanks
For model number JCB840SF3SS
Hello Walter, thank you for your question. We did find your model and the Knobs are sold individually as part PS9864386.
1 person found this helpful.
Did this question help you?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Ordered new Parts. Removed old/worn parts. Found that the "hammering" from a loose pulley had worn and deformed the edges of the shaft where the flats are to accept new pulley. Gently filed the flats with the flat surface of the file and filed the hump on the shaft that the "hammering" created. Take extreme caution to not file surfa
... Read moreces too much, because new pulley will be loose and the next step is to replace the drum shaft.($$$$) Pulley did not fit 100% (Had some slop) but that was from material being worn away from "hammering" effect. Torqued with Torque wrench and added green 609 loctite compound - this is meant to help adhere and take up some loose fit in assemblies. - Drawback to Loctite is most have to be heated to 300 to 400 degrees to remove, or pulley will need to be cut off and ruined, I further repair/removal of pulley is necessary. This is an Easy Fix/Replacement of parts.... The hard part is filing the drum shaft surfaces to accept the new pulley, and getting the belt back on - Belt is tight but needs to be stretched on like putting a bike chain back on.
Washer now spins and sounds like a dream! - Good Luck!
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the c
... Read moreatch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
My husband put on the defrost timer. At first I thought the part was not going to fix the problem. After about 5 hours my refrigerator was still warm. I went to work and when I got home that evening my refrigerator was cooling and down to 28 degrees. So if you replace this part wait at least 12-24 hours. Give it time to stablize.
... Read moreMy husband says it has to go through its cycle. It works on a 24 hour timer. My refrigerator is working fine and this has saved me alot of money. My husband says, once you put on the timer you may have to use a flat screwdriver and turn the small dial clockwise one click to start it. He removed the kick grill and replaced the part. Dont forget to shut breaker off to replace this part. Turn power back on and start the timer. We are so happy that we now have a working refrigerator.
