Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature ...
This genuine GE drawer support is an original replacement part sourced from the manufacturer and is designed for use with electric ranges. Made of durable plastic, it attaches to the rear of the drawe...
This infinite control switch regulates the power delivered to a surface heating element, allowing precise temperature control during cooking. It functions by cycling power on and off based on user inp...
This surface element control switch, also known as an infinite switch, regulates the power supplied to a 6-inch, 1560-watt heating element on electric ranges. It allows for precise adjustment of heat ...
This dual radiant surface heating element is a genuine replacement component designed for select GE electric flat-top ranges, stoves, and cooktops. Commonly referred to as a "haliant" element, it feat...
This is a dual ceramic surface burner for ranges. This burner, also known as a heating element, is used within electric ranges to act as a stovetop burner. This burner measures approximately 10 inches...
This window pack assembly, also known as inner door glass, is supplied directly by the manufacturer for use in range ovens. It has measurements of approximately 22 inches by 14 inches. The inner door ...
Here's a part you may need: the GE Transmission Pulley. This essential piece helps your appliance work at peak performance smoothly and efficiently. Produced by the trustworthy GE brand, it's a durabl...
This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
$64.77
In Stock
Order now and your part arrives by May 24
Questions And Answers for JB750SJ3SS
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Philip
December 22, 2023
My oven is not maintaining temperature. For example, if I set it for 425, it gets up to temperature and says that it's 425, but five minutes later the temperature has started dropping. If I cancel and restart at 425, it will show the real (lower) temperature, and climb back up to 425. Also, I generally need to set it for 475 if I actually want to hit 425. So, I constantly have to cancel and restart to maintain a certain temperature. It's been doing this for at least a year. I have replaced the temperature sensor. Thanks!
For model number JB750SJ3SS
Hi Philip, thank you for contacting us. As you have already replaced the temperature sensor, we would recommend checking the door gasket. If that is not the case, then you may need to replace the control board and overlay assembly, part number PS12725906, to fix the issue. The control board and overlay monitors temperature and control the oven heating functions in the range. Good luck with your repair!
Hi Lavonne, thank you for getting in touch. To replace the bake element, part number PS2370383, we would suggest following these general instructions: Open the range door and pull the racks out. Remove the screws holding the bake element on the side. Pull the bake element slightly, and remove the wires. To install the new bake element, connect the wires and put the screws back in. We hope this helps!
Hi Christine, thank you for the question. The F720 code is a main logic board internal touch key chip signal error. To solve this issue, you may need to replace the oven control and overlay assembly, part number PS12725906. We hope this is helpful!
when i set my oven to 350 its goes back down to 100 preheat which part should i switch out
For model number JB750SJ3SS
Hi Marcus,
Thank you for your question. If the range is not heating correctly, the issue is likely the temperature sensor, part number PS10059162, and it will need to be replaced. We hope this helps!
My oven would not heat beyond 175, replaced sensor, still taking excess amount of time to heat up. It has now been on for 2 1/2 hour, still has not reached 350
For model number JB750SJ3SS
Hi Lavonne, thank you for your inquiry. Since you have already replaced the temperature sensor, we recommend replacing the oven control board, part number PS12725906. We hope this information helps!
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U
... Read morenscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.
