Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This part is a halogen lamp, but it may also be known as a light bulb and is an important part for your range. This model is 75 watts and measures to be roughly 3 inches high, and 2 inches wide. The p...
This range hood trim lamp assembly provides bright, reliable lighting for the cooking area beneath the hood, replacing a light that is dim, flickering, or no longer working. Designed for a precise fit...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
February 27, 2024
The Dacor Hood light trim ring came loose while replacing the bulb. It appears to fit with a spring but is not snapping back into position.
For model number IVS1
Hi Michael, thank you for your inquiry. To snap the light trim ring back, you may compress the springs of the ring, and insert it in the slot. Once it is inserted, you may release the springs then. We hope this solves your problem!
Did this question help you?
Thank you for voting!
Mark
November 19, 2024
The knob for the light does not click and engage.
What part do I need to fix it. There's a metal box above for each switch. Does the whole box need to be replaced or something inside of it for the knob?
For model number IVS1
Hi Mark, Thank you for writing. For this model the knob connects to the Shaft for the Lamp Dimmer Switch, PartSelect Number PS16631994 and the switch will need to be replaced. We hope this solves your problem!
I had to remove the underside sheet metal (two separate parts) by unscrewing the screws securing them to the hood. The sheet metal piece that covers the fans had to be fully removed to be able to access the sheet metal part to which the light sockets are attached. There are vertical legs that connect this second assembly to the roof of
... Read morethe range hood so this part could not be removed to work on it. I was able to move this part enough to get vision on the brackets that held the light sockets In place. I removed the old light sockets and the rivets securing the internal electricity conduction parts of the socket were loose and trying to solder them did not improve their ability to make good contact and keep the bulbs lit. I therefore had to order replacement sockets. The shipment of these sockets was delayed and I had to put the range hood back together for Christmas Eve party so I found a different type of ceramic socket at the local hardware store and I was able to use those to replace the defective sockets that came with the range hood. I was actually happy with this different socket because I felt that the quality of design and materials in the factory socket would lend itself to malfunction again in the future. The new design socket that I installed seemed far more sturdy and less likely to fail in the future. Unfortunately these new sockets were slightly shorter in length than the ones I was replacing. As a result I had to modify the Dacor light trim rings to allow the bulb to screw in about a 1/4" further than the stock socket required. All in all about a 4-5 hour job with a trip to the hardware store and lots of research on line. I will say that despite contacting appliance repair companies all around the Bay Area, I did not find one that was willing to work on my Dacor Range Hood. That's why I had to do the DIY thing. Now I'm an expert.
In order to grasp the bulbs, which are flush against the vent surface, you need the 'Suction Cap' tool. However, the bulbs are solid tight in their sockets from years of heat over the stove. Removing the vent filter allowed access with a small plier to the base of the bulb allowing me to loosen the bulb. Don't have a suction cap? Wrap du
... Read morect tape around your two fore-fingers, press tightly against the face of the bulb and twist counter-clock wise. I recommend apply some Vaseline jell to the new bulb thread to keep the fitting from freezing.
Purchased a screw extractor set from the local Ace Hardware (SpeedOut). Be sure and carefully follow the screw extractor instructions as written (counterclockwise turn). Removed old screws and replaced them with new screws supplied by PartSelect.
