Models > HDA2100V35WW

HDA2100V35WW Hotpoint Dishwasher - Overview

Sections of the HDA2100V35WW

[Viewing 3 of 3]

Manuals & Care Guides for HDA2100V35WW

Click to download
Keep searches simple, eg. "belt" or "pump".
Lower Rack Wheel Kit - 8 Pack – Part Number: WD35X21038
Lower Rack Wheel Kit - 8 Pack
★★★★★
★★★★★
(156)
PartSelect #: PS11726733
Manufacturer #: WD35X21038
This lower rack wheel kit includes 8 wheels and 8 axles that allow the lower dishwasher rack to slide in and out smoothly. If your dishwasher door will not close, is noisy when operating, or the dishe...
$36.85
  In Stock
RACK SLIDE END CAP – Part Number: WD12X10304
RACK SLIDE END CAP
★★★★★
★★★★★
(52)
PartSelect #: PS2370502
Manufacturer #: WD12X10304
The Rack Slide End Cap is a white one-inch plastic part which replaces the end cap for your dishwasher rack, preventing your rack from sliding too far. If you find the dish rack is causing the door to...
$12.61
  In Stock
Corner Tub Baffle - Lower Right – Part Number: WD8X227
Corner Tub Baffle - Lower Right
★★★★★
★★★★★
(12)
PartSelect #: PS263963
Manufacturer #: WD8X227
This baffle fits the lower right hand corner of some dishwashers. It is black rubber and has a matching left hand lower corner baffle. It is recommended that you replace and install both left and righ...
$25.90
  In Stock
Corner Tub Baffle - Lower Left – Part Number: WD8X228
Corner Tub Baffle - Lower Left
★★★★★
★★★★★
(19)
PartSelect #: PS263964
Manufacturer #: WD8X228
The corner tub baffle may also be known as the door baffle and is a part used on your dishwasher. The left and right side baffle on your dishwasher should be installed and replaced at the same time. T...
$23.85
  In Stock
LOWER RACK – Part Number: WD28X31819
LOWER RACK
★★★★★
★★★★★
(69)
PartSelect #: PS17137102
Manufacturer #: WD28X31819
This part includes the wheels.
$205.27
  In Stock
Door Gasket - White – Part Number: WD08X10057
Door Gasket - White
★★★★★
★★★★★
(18)
PartSelect #: PS958908
Manufacturer #: WD08X10057
This one piece dishwasher door gasket provides a water tight seal to keep water from leaking out of your dishwasher.
$133.00
  In Stock
Water Inlet Valve – Part Number: WD15X10014
Water Inlet Valve
★★★★★
★★★★★
(54)
PartSelect #: PS3654179
Manufacturer #: WD15X10014
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve open and close according to the desired amount of water needed.
$43.78
  In Stock
Interlock Switch – Part Number: WD21X10261
Interlock Switch
★★★★★
★★★★★
(18)
PartSelect #: PS1481922
Manufacturer #: WD21X10261
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. ...
$27.42
  In Stock
Push On Nut – Part Number: WR2X7054
Push On Nut
★★★★★
★★★★★
(7)
PartSelect #: PS298353
Manufacturer #: WR2X7054
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
$13.82
  In Stock
Hinge Arm Link – Part Number: WD14X10009
Hinge Arm Link
★★★★★
★★★★★
(9)
PartSelect #: PS259336
Manufacturer #: WD14X10009
The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In ...
$8.54
  In Stock
Rinse Aid Fill Cap – Part Number: WD12X10284
Rinse Aid Fill Cap
★★★★★
★★★★★
(11)
PartSelect #: PS2351824
Manufacturer #: WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
$18.39
  In Stock
Screw 8-16 hxw 1/2 Stainless Steel – Part Number: WD02X10067
Screw 8-16 hxw 1/2 Stainless Steel
★★★★★
★★★★★
(2)
PartSelect #: PS258461
Manufacturer #: WD02X10067
Sold Individually.
$8.54
  In Stock

Questions And Answers for HDA2100V35WW

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Frank
December 2, 2019
How do i remove the filter it has a drain going into the middle of the filter cant lift the filter out
For model number HDA2100V35WW
PartSelect logo
Hello Frank, Thank you for your question. You will need to remove the bottom spray arm to remove the filter. On the side of the base of the arm there is a tab you will need to pry outwards a bit with a small flat head screw driver to release the spray arm. It is off to the side on the back side so it is not easily seen. You may have to feel around to locate the tab. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Brian
February 1, 2024
the water does not drain. I have checked for restrictions throughout the system including the line going to the garborator. I have removed and cleaned out the interior filters of the unit. The clinoid appears to work, however, water remains. I am wondering if the clinoid although it moves is not working. Any suggestions before I order the clinoid unit? Thanks
For model number HDA2100V35WW
PartSelect logo
Hello Brian, thank you for getting in touch. According to our research, we would recommend checking the drain solenoid carefully for any fault. If the drain solenoid is completely fine, then the issue is most probably with the drain pump. The drain pump comes along with the pump and motor assembly, part number PS3486941. You may need to replace it to solve the problem. Glad to be of assistance!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1

Common Symptoms of the HDA2100V35WW

[Viewing 12 of 12]
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Not cleaning dishes properly
Fixed by
these parts
Fixing Fixing Fixing
Show All
Not draining
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not dispense detergent
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door latch failure
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing
Show All
Will not fill with water
Fixed by
these parts
Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing Fixing Fixing
Show All
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Not drying dishes properly
Fixed by
these parts
Fixing Fixing
Show All
Won’t Start
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Parts Used:
Lower Rack Wheel Kit - 8 Pack
  • Mark from Huntingdon Valley, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
520 of 542 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The rear wheels were missing on the lower rack.
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
Parts Used:
Lower Rack Wheel Kit - 8 Pack
  • Teresa from Phenix City, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
474 of 486 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing machine would cease functioning at the spin cycle and would not drain.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.
Parts Used:
Motor and Drain Pump
  • Trent from Shreveport, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
153 of 182 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!