Models
>
HA106
HA106 Maytag Washer - Overview
Sections of the HA106
[Viewing 17 of 17]
Keep searches simple, eg. "belt" or "pump".
Rubber Foot Pad
PartSelect #: PS11738859
Manufacturer #: WP210684
The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is ju...
$15.28
In Stock
Washing Machine Lid Hinge Ball
PartSelect #: PS11738871
Manufacturer #: WP211726
This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Ma...
$11.14
In Stock
Adjustable Leveling Leg
PartSelect #: PS2021026
Manufacturer #: 22003428
If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs ...
$18.47
In Stock
Spring Retaining Clip
PartSelect #: PS11739294
Manufacturer #: WP22001650
This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than ...
$11.10
In Stock
Washer Lid Bumper
PartSelect #: PS11738875
Manufacturer #: WP212716
This washing machine lid bumper is just under an inch long. It is all gray in color and is made entirely of rubber.
$7.70
In Stock
Screw & Fastener Kit - Front Panel
PartSelect #: PS2017075
Manufacturer #: 204439
No Longer Available
Screw - 12-14 x 1/2 Type B
PartSelect #: PS11740594
Manufacturer #: WP27001200
Sold individually.
$5.36
In Stock
Screw
PartSelect #: PS11743719
Manufacturer #: WP67006908
Model Number GB2526REKS :
SCR
$8.04
In Stock
Questions And Answers for HA106
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the HA106
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washing machine lid came off during a move
First, I secured one lid hinge ball in its appropriate position between the lid and the washer. While keeping the first ball in place I placed the other lid hinge ball as close to its intended position as I could get it. Next, I pushed the lid and ball into its position.
Parts Used:
-
David from New Orleans, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
30 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stripped leveler screw making impossible to level my washer
Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy.
Parts Used:
-
Rebecca from Wylie, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
21 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing machine lid hinge balls fell off machine lid
First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixe
... Read more
d to your machine where you can lift the lid and it will stay up without falling.
Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.
Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.
Read less
Parts Used:
-
Sandra L from Warren, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!