Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GX900QPKQ0

GX900QPKQ0 Whirlpool Trash Compactor - Overview

Get Parts and Repair Help for GX900QPKQ0

If you know the trash compactor repair part you need, you can browse the list of all parts on the GX900QPKQ0, or you can search by name or part description. You can also find your part by where it is located on the GX900QPKQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your trash compactor. We’ve also included any installation videos we have for GX900QPKQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for GX900QPKQ0

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$26.93

Drive Gear Kit

This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your com...

$2.81

Foot, Front - Single

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.

$7.36

Container, Bearing Roller

This bearing roller may also be known as the wheel assembly or the container roller bearing, and it is a piece for your trash bin. The function of this bearing is to work in conjun...

$34.61

Directional Switch

The function of the directional switch on your trash compactor is to ensure the ram lowers to compress your trash, then returns to the top position. If your trash compactor does not complete this task, will not stop at the end of the compacting cycle, or is noisy during operation, you may need to replace the directional switch. Be sure to disconnect your trash compactor from the power source before completing this repair. This is a fairly easy repair. After you open the control panel of the compactor, all you will need to do is unplug the old switch from the electrical wires, and plug the new switch in.

$11.94

15" Compactor Bag Carrier with Easy Grip Handles

This 15 inch compactor bag carrier fits around the compactor bag inside the compactor and is used to easily lift and remove trash compactor bags once they are full. Simply place th...

$2.96

Screw

Sold individually.

$81.10

Handle, Container (Black)

Screws sold separately.

$33.33

Foot Pedal

This replacement part is a foot pedal which fits on a trash compactor. It includes two screws for installation. The pedal mounts on the footplate on the bottom front of the container. The pedal controls the container drawer. When stepping on your trash compactor pedal, the latch should release the container from the compactor body. This foot pedal is black, made of plastic, and is sold individually. Be sure to disconnect power to your appliance before beginning this repair. You will only need a screwdriver to complete the repair. This is a genuine part and is sourced from the authentic manufacturer.

$20.15

Wheel Assembly - Kit of 2

This wheel assembly, or roller assembly, is for a trash compactor. The kit includes two wheels that are approximately 1 inch in diameter each. The wheels allow the trash compactor ...

$2.96

Single Metallic Shoulder Screw - Size: 8-32 x 3\8"

Sold Individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Compactor stuck in lower position

  • Customer: Asbjorn from The Woodlands, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 41 of 50 people found this instruction helpful
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way.
Removed the driv... read more

Trash Compactor ram wouldn't lower

  • Customer: Scott from Indianapolis, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 29 of 32 people found this instruction helpful
I pulled the trash compactor out from under the counter.

I took out the four screws that kept the top cover in place to expose the ram.

The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit s... read more

Scratches in Surface

  • Customer: Michelle from Richardson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 24 of 33 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. read more