This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and ...
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your wa...
This drive belt is sourced from the original manufacturer for use in various models of dryers. It is a rubber belt that connects the motor to the transmission of the washer. It enables the drum to spi...
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This is an inlet valve for models of compatible washing machines. Inlet valves are electrically controlled solenoid valves that open and close as needed during the washing cycle, to allow water into t...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
November 17, 2022
looking to see if this washer has a filter, if so where is it located
For model number GTW685BSL0WS
Hi David, thank you for contacting us. Your model does not have any filter. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Betty
June 19, 2023
Machine starts by itself. Will not turn off with power button.
For model number GTW685BSL0WS
Hello Betty, thank you for your inquiry. Based on our understanding of the issue, we would suggest checking the user interface control board, part number PS12743633, to fix the issue. It processes the cycle settings you choose. The interface also houses the display for the washer. We hope this solves your problem!
washer sounds like a belt or chain is hitting the outer shell
For model number GTW685BSL0WS
Hi Anthony, thank you for reaching out. Based on our research, the issue is because of the drive belt, part number PS11736832. We would recommend replacing the drive belt to fix the issue. We hope this solves your problem!
Wouldn’t drain min left light flashing and power shut off the outlet has power supply
For model number GTW685BSL0WS
Hello Barb, thank you for your inquiry. Based on our understanding of the issue, we would suggest checking the control board, part number PS17139249, to solve the problem. We hope this helps.
I just replaced the water valve assembly because water was dripping non stop into the tub but now the tub is over-filling and says h20 supply and then drains out. Water no longer drips into the tub though...
For model number GTW685BSL0WS
Hello Lesley,
Thank you for your question. We suggest using a multi-meter to check the water valve you ordered from us to make sure it isn't defective. Typically if the washer is overflowing or if there is a leak its both caused by the valve itself since it controls the water output. We hope this helps.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Use putty knife to unlock top panel from base. Remove 2 bolts from back of washer holding control section. Don't take completely off. 2 bolts needs to be removed to unsecure top from base. Lastly 2 screws hold lid in place. Remove lid. Slide top panel to left just to access lid lock. Unplug sensor. 1 screw and tabs hold lock in place. Wat
... Read morech position coming out so you don't get confused putting new lock in. Squeeze tabs, replace screw. plug in sensor. Reverse procedure to put top section back together.
