Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
This lint filter is a genuine OEM component designed for use in both electric and gas clothes dryers. It plays a critical role in maintaining proper airflow by capturing lint and debris during drying ...
This drum glide bearing is an authentic OEM replacement part that is compatible with dryers. It is white in color and made of highly durable plastic. The bearing allows the drum to rotate smoothly and...
This OEM replacement dryer slide bearing is white in color, and approximately 3 inches long. The slide bearings are supportive linings for your dryer. If they have eroded, or are damaged, the drums wi...
This is the door switch for your dryer. Door switches are used to communicate with the control board when the door is fully closed, so the drying cycle can safely begin, and if it is opened so it can ...
This authentic OEM rear bearing O-ring is designed for use with GE dryers. It helps secure the drum rear bearing onto the drum shaft, playing a key role in maintaining smooth and quiet dryer operation...
Experience the seamless functionality of your dryer with the GE Door Hinge. This dryer component plays a crucial role in the operation of your machine, supporting the dryer door on its front panel. It...
This dryer door latch is designed to securely fasten the door to the cabinet, ensuring safe and reliable operation during each cycle. Made from durable gray materials, it engages with the door strike ...
This fastening nut secures components firmly in place, helping maintain proper alignment and safe operation. It is commonly used as a replacement when original hardware is stripped, lost, or damaged.
$18.30
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for GTD75ECPL1DG
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Catherine
July 22, 2023
My ge dryer model#gtd75 has stopped working. I left the door open for 12 or so hours. After that, it doesn't even come on. Any ideas?
For model number GTD75ECPL1DG
Hi Catherine, thank you for reaching out to PartSelect. If your dryer is not starting, we recommend checking the door switch, part number PS12722948. We hope this sorts out your problem!
I just replaced the dryer bearing top assembly (WE03X23875) after a drywall screw got caught between the lip of the drum and the bearing assembly. The screw broke two of the plastic tabs that held the bearing slides in place.
After reassembly, the "Air Fluff," "Steam Dewrinkle," and "Steam Refresh" settings on the selector do not work. I do hear the relay activate for the steam settings. In addition, the other modes will only run for 2 minutes before the dryer stops.
I can start the dryer again after 5-10 minutes but it stops after a 2 minute run time.
I entered the field service mode and no error codes are reported. That being said, the drum does not engage in test "T11," the Water valve test, nor does it spin when in test "T13," the Drum test.
Any advice would be greatly appreciated.
For model number GTD75ECPL1DG
Hello Brian, thank you for reaching out. The issue you described could most probably occur due to a malfunctioning control board. We would recommend checking the control board, part number PS12722950, to solve the problem. We hope this helps!
I push the start button and it inky "clicks" The click is only one time and does not start. I ordered Start Switch, Interlock Switch, and Push-to-Start Switch. Do your knowledge should I have ordered anything else? The closest part stores are over 2 hours away. Thank you for replying
For model number GTD75ECPL1DG
Hi Bill, thank you for reaching out. According to our research, the single click is often the sound of the motor relay trying to turn the motor, but if the motor is seized or faulty, it will just hum or click and stop. You may need to replace the drive motor, part number PS12743452, to fix the issue. We hope this solves your problem!
when the dryer spins, its got a scratching sound on the right hand side of the drum, what causes that?
For model number GTD75ECPL1DG
Hello Jay, thank you for reaching out. Based on our understanding of the issue, we would suggest checking the drive belt, part number PS16542496, to solve the problem. Glad to be of help!
Some of the buttons on the front control panel aren’t working.
For model number GTD75ECPL1DG
Hi Matt,
Thank you for your question. If some of the buttons on the control panel are not working, you will need to replace the electronic control board, part number PS12722950. We hope this helps!
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.
I had to take most of the dryer apart because there is no rear access to the motor. It turned out to be easy to dissasembel the dryer. The only problem that I had was that I could not figure out how to route the belt around the motor and the idol pullies. I could not find anywhere that gave instructions on how to properly tension the belt
... Read more. I finally figured out that the idoler pulley needs to be locked in place on the right side of the engie mount. Then the belt needs to be routed over idoler pulley and under the motor pulley. Finally release the idoler pully from the locked postion to put tension on the belt. It really turned out to be pretty easy.
Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a
... Read moresnap.
