Parts That Fix General Electric Refrigerator GSS25LSLJCSS Fridge too warm

This compression ring is meant to hold the evaporator fan motor in place in the freezer compartment of your refrigerator. This is is a genuine OEM part. The tools needed to complete this repair are a Phillips screw driver and small flat blade screw driver. Be sure to turn off your refrigerator before removing the evaporator fan cover so the fan does not turn on during repair. It is recommended to check the grommets, evaporator fan, and fan blades during repair in case they also need replacning. The compression ring may need replacing if the fan is noisy, or the refrigerator compartments are too warm. This part is sold individually.

Includes the wiring harness and thermistor. This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.

This part is the replacement fresh food door gasket for your refrigerator. It is made of black rubber and is sold individually. The fresh food door gasket runs along the circumference of your refrigerator’s fresh food door and creates the seal that allows your refrigerator to regulate the temperature inside. If the gasket is worn, stretched, or damaged, your fridge may become too warm, and you may notice the door is sweating. The door also may not open or close properly because of a damaged gasket. To replace the gasket, carefully pull the old gasket out the grooves it fits in around the door. Press the new gasket into the same grooves snugly. This part is an OEM part from the manufacturer.

Stay confident about the longevity of your refrigerator with the high limit thermostat from GE. This practical thermostat serves as an essential part of your refrigerator's defrost cycle. With the purpose of preserving the evaporator, it utilizes a defrost bi-metal design, preventing the possibility of overheating. To ensure safe installation of the thermostat, always remember to unplug the refrigerator and don a pair of work gloves for added protection. Maintain the efficiency of your appliance with this commendable GE High Limit defrost thermostat. For optimal performance, always put away any food that could spoil when the power is turned off.

The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.

This “Dispenser Door Assembly” (Door Recess Assembly, Ice Door Assembly, Dispenser Door, Refrigerator Dispenser Ice Chute Door Kit, Dispenser Door Flap, Ice Chute Door, Flapper) keeps the room air from infiltrating the freezer. Once the lever is pressed, the door flap opens and allows the ice to dispense into your container. If your door flapper is broken, it could allow outside air to enter the freezer and alter the inside temperature. You may notice frost buildup surrounding the dispenser area. The door flap can disconnect from the dispenser lever, or the tabs that hold it in place may break. Frequent use may distort the sealing face and cause air leaks and frost buildup. This part mounts in the ice dispenser, and measures approximately 3.25 inches in diameter. It is constructed of plastic and rubber, and comes in white/black. This part is sold individually.

This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unusually noisy, it could be because the grommet is damaged. This grommet is made of grey plastic and is approximately one inch in diameter. To access the fan grommet and complete this repair, you will need to remove the evaporator fan motor assembly. This part is sold individually.

This OEM ice and water filter fits side-by-side and bottom-freezer GE models. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water. This also may lead to your refrigerator not dispensing water or ice properly. Manufacturers recommend you change your filter every six months to ensure it properly filters impurities. Depending on the model, a red light might also indicate that the filter is due for a replacement. Note: As per the manufacturer, this is an updated water filter. If you have never installed the updated part or your old model was made by Culligan, you may need the adapter to install the filter. See related parts. This filter is located inside the refrigerators upper right corner. It is common for water to drip from the dispenser when being changed so place a cloth underneath before you begin this repair. To remove the filter, turn it to the left until it releases without pulling down. Fill the new filter with tap water to prepare it. Position the new filter into the holder taking note of the arrows. The arrow on the front should be facing out. Gently push up on the filter and turn it to the right to secure it. Do not over-tighten. To release air in the system run 1-1/2 gallons of water through it. If your model has a reset button, press and hold this for a few seconds to reset it.

Introduce your refrigerator to a seamless cooling experience with this GE Condenser Fan Blade. Designed exclusively to fit into specific models of GE refrigerators, this fan assembly ensures your appliance runs at peak efficiency. It expertly moves air across the condenser coil to adequately cool the hot refrigerant before it enters the evaporator. To maintain the freshness of your perishables, it is advised to safely store any food that might deteriorate during the installation process. Remember to unplug the refrigerator before commencing with the installation of this essential component. Keep your refrigerator at its optimal cooling state with this top-tier GE Condenser Fan Blade.