GSD3300D00WW General Electric Dishwasher - Instructions

There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.

Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.

The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.

Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.

Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.

1. I removed the plastic stops from the ends of the upper rack slides.
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away

First off on this model, if one of the telescopic spray arm weld assembly comes out it is NOT repairable you have to replace the whole part.
The assembly on my model number was simple you do NOT have to PRY anything out...(I broke the base spray arm trying to shove a screw driver into the Spray arm weld.(You could try this but chances are the plastic will break and I recommend replacing both parts why not???.)
There are two bolts on the sump protector basket that has to be removed first. They are 1/4 inch.
Once that cover is free there is a bolt (also 1/4 inch) on the base spray arm it is easy to see but hard to get to I used a very thin open ended wrench
1/3 turn at a time till I could get the socket on it.
Next there is a rubber gromet like thingy that just pulls loose remove it also.
Next take the spanner wrench (I used one with a rubber belt) wrap around base spray arm and turn counter clockwise it just unscrews.

reassembly is simple but this is GE so I inspected the sump and found one medal impeller and one black screw at the bottom!!!!!
The impeller is threaded and just screws onto the shaft (look at the diagrams on this web site to see placement.)
Throw the screw away it does nothing except if left there jacks up the impeller I am guessing it fell out of some factory workers pocket.
If after you put all the parts back in and the washer does not drain check your reassembly if you don't line the parts up just right the unit will not drain.
Don't forget the rubber grommet (not sure what it does but it's easy to replace after all is assembled) also there is a metal washer that is inbetween the base spray arm and the spray arm weld put it back before you click those two parts together it protect the plastic from wearing it is a bearing!!
If you found this site you are doing really good This site had all the diagrams I was looking for I love you guys you so rock!!! I wish the diagrams were bigger but they were adequate. GE 's site was no help and I doubt I will ever buy another one from them.
Good luck just remember look at the parts diagrams before attempting the repair.

replaced rack, no repairs required

lower rack took one min. take out old slide in new

upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off.
total time for this part 15 min.

You'll need to remove the front toe kick and (if installed, the GE Profile baffling for additional silencing action).

You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.

You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.

Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.

Reverse the order and reconnect everything and you should be good to go!

Double-check for any leaks prior to pushing everything back in :)

Siimply removed the rack and replaced the wheel assembly. Very easy

Very easy about 5 min replacement, Checked electrical conductivity to verify I had a bad solinoid, after I received the new part. I removed and replaced part by only removing and re-installed 2 screws and spring. Dishwasher worked like new.

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

To remove the upper rack guide end caps, pull the inside flange gently to the rear, then twist the cap out of the track. Then the rollers come out easily, and replacing them involves merely snapping them in place over a rack frame part. Piece of cake! Roll the rack back into the guides, and replace the end caps. No tools needed!