Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GS2327PEHQ

GS2327PEHQ Maytag Refrigerator - Overview

Get Parts and Repair Help for GS2327PEHQ

If you know the refrigerator repair part you need, you can browse the list of all parts on the GS2327PEHQ, or you can search by name or part description. You can also find your part by where it is located on the GS2327PEHQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for GS2327PEHQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$5.40

Screw

Sold individually.

$4.88

Screw

Sold individually.

$5.27

Lower Hinge Pin

This is a lower hinge pin for your refrigerator door. This hinge helps your door open and close easily by allowing it to pivot. You will need to replace your lower hinge pin if your refrigerator door will not open or close properly. This part is almost two inches high, one inch wide, and roughly two inches long. You will need a Phillips screwdriver and a 5/16 nut driver to replace this pin. It is made entirely of plastic and is all black.

$5.47

Crisper Drawer Shelf Support

This crisper drawer shelf support is used for many refrigerators. It is all white in color and is made entirely of plastic. This shelf support is less than an inch long.

$24.22

BLADE-FAN

The fan blade is used to blow air over the condenser.

$2.96

Screw

Sold individually.

$2.96

Roller Screw

This screw is less than an inch long, and is made entirely of metal. It is used for the roller of many Maytag brand refrigerators.

$30.64

Thermostat Order 542369 Cement

The ice maker thermostat, also known as the cycling thermostat, controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine wh...

$17.57

Water Fill Cup and Bearing

This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ice maker is leaking, or not making/dispensing ice. If you notice the fill cup has been damaged or cracked; replace the part straight away. This water fill cup is a genuine OEM part and will fit most refrigerators, but check the list of compatible brands to make sure yours is included before purchasing.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 95 of 115 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more

No ice in ice trey

  • Customer: Wayne from Leesburg, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 74 of 92 people found this instruction helpful
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and star... read more

cocktails running out of ice

  • Customer: Craig from Westminster, CA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 52 of 57 people found this instruction helpful
filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : ) read more