The silverware basket, used for dishwashers, is in the bottom of the dishrack. The basket is used to hold eating utensils such as spoons, forks, and knives. If the basket is worn out or broken, you sh...
$91.04
In Stock
Order within the next 0 mins and your part ships today!
The drain valve shaft seal is a part for your dishwasher drain pump valve. This seal creates a watertight closure around the flapper valve shaft. This part can be accessed through the access panel at ...
$36.05
In Stock
Order within the next 0 mins and your part ships today!
This is a pump and motor kit for your dishwasher. This assembly replaces many old-style pump and motor kits that were manufactured since 1970. The instructions are included with this kit in to assist ...
$249.86
In Stock
Order within the next 0 mins and your part ships today!
This water inlet valve is specially designed for those dishwashers that fit under the counter from 1974 To Present. The valve should be located behind the lower kickplate panel in either the right or ...
$57.50
In Stock
Order within the next 0 mins and your part ships today!
The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able...
$16.51
In Stock
Order within the next 0 mins and your part ships today!
The impeller and seal kit is used in a dishwasher. The kit includes all the parts needed to do this repair, including the impeller, seal, blade, filter, skidder and skidder holder. If your washer is l...
This is the replacement upper spray arm water supply hose for dishwasher. It is made of white plastic and has a connector piece on each end. This hose supplies water to the upper spray arm, so it can ...
Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying water and detergent onto the dishes on the dishrack. This spray ar...
$86.81
In Stock
Order within the next 0 mins and your part ships today!
This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of y...
$34.01
In Stock
Order within the next 0 mins and your part ships today!
I had never done work on my dishwasher - I was a rookie in this area. Turns out the work itself was quite simple. Pulled the dishwasher out, turned it over, and was able to easily replace the motor and pump assembly. The drain tube was also an easy replace. A couple key notes:
1. I also purchased a new drain solenoid and impell
... Read moreer kit. Note that both of these items are already included in the Motor and Pump kit replacement. There is no need to by both, now I have extras.
2. The end of the drain tube has to be trimmed if you are routing the drain tube to an air gap mounted on your kitchen sink. You have to cut the large diameter end of the tube to get to the narrow portion that will fit on your air gap.
3. The first cycle you run with the new motor/pump assembly is noisy. When you first fire it up the components in the pump are all dry, and they squeal until the water gets to them. I initially thought I had done something wrong, but once the water started flowing all the peculiar sounds cleared up.
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. T
... Read morehis easy repair solved the problem.
1. Remove lower cover skirt. 2. Shut of water at undersink valve. 3. Unplug power cord or turn off circuit breaker. 4. Disconnect water supply line from fill valve. 5. Unplug the electrical connector from the valve. 6. Remove the 2 valve mounting bracket screws. 7. With loose valve in hand, rotate to g
... Read moreain access to allow release of outlet hose clamp for hose removal. 8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
