Parts That Fix Frigidaire Washer GLTF2940FS1 Leaking
Leaking is a commonly reported symptom for the GLTF2940FS1 Frigidaire Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GLTF2940FS1 Frigidaire Washer that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
The water inlet and dispenser valve is used in washing machines. The function of this part is to control and monitor the amount of water flow into the washer. If there is leaking during use, your machine will not fill with water, or there is no hot or cold water entering the washer, it is important to replace the water valve to solve the problem. For this repair, you will need a Phillips head screwdriver and a flathead screwdriver. For installation instructions, refer to the manual provided by the manufacturer. Remember to unplug your appliance from the power source before beginning this repair.
Customer Repair Stories
Frozen pipe
-
Frank from Auburn, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Valve dispener would spray water all over inside of washer.
-
Julie from Lancaster, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle. NOTE: This part has been redesigned by the manufacturer and is interchangeable with the old design.
Replacing your Frigidaire Washer Bellow Kit
Customer Repair Stories
Moldy smelly rubber cowl around door.
-
Emil from BOULDER, CO
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
Old Bellow Ripped
-
Peggy from New Castle, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Also known as tub-to-pump drain hose.
Replacing your Frigidaire Washer Drain Hose
Customer Repair Stories
The drain house was penetrated by a piece of metal from coin catcher
-
Kimberly from East Moriches, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
Replacing your Frigidaire Washer Spring-Held Bellow Clamp
This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.
Replacing your Frigidaire Washer Shock Absorber Kit
Customer Repair Stories
Tub loose
-
Mel from Ipswich, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
Both vibration shock absorbers broken
-
Douglas from Medical Lake, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not start or spin, you may need to replace the door strike. This part is for front load washers and is white in color. The part is made of plastic and is roughly 2 inches in length. To complete this repair, you will only need a Phillips screwdriver. Most of our customers found this repair to be easy and took less than 15 minutes to complete it. This part is sold individually, not as a part of a kit, and is a genuine part approved by the original manufacturer.
Replacing your Frigidaire Washer Door Strike
Customer Repair Stories
washing machine front loader door would not close, making the machine useless
After looking all over for the part,and no ... Read more t finding it I was thrilled when you carried the part. Even though the machine is old, it works great. Thank you for the selection of all the parts you carry and how you make it so easy for us to find what we need. , and having it in stock, which was mailed right away, so I could replace the catch and have the washer back in use in less than a week. Thank you
-
Susan from Vero Beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Broken Door Catch
-
Joy from Columbia, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
Replacing your Frigidaire Washer Drain Pump - 120V 60 Hz.
Customer Repair Stories
After a full cycle the washer would not drain the water
-
sara from North Miami, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
would't spin all water out or rinse out clothes
-
kenneth from willard, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Replacing your Frigidaire Washer Dispenser to Tub Hose
This part is located between the front and rear outer tubs.
This is the replacement bottom panel or access panel for your dryer or washer. It is white in color and is approximately 28 inches wide and 10 inches tall. The access panel can be removed from the bottom of your dryer, so you can access the parts behind it. The main reason that you would want to replace the panel is if it is damaged, or it will not stay attached to the dryer. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Replacing your Frigidaire Dryer Bottom Panel - White
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the door does not open or lock. Your washer will not start if the door does not lock. This part is also known as a washing machine door lock assembly. As per the manufacturer, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.
Replacing your Frigidaire Washer Front Load Washer Door Lock and Switch Assembly
Customer Repair Stories
Washer would not spin
-
Keith from Sayville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Door on washer wouldn't lock or start
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
-
DOUG from KING FERRY, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Replacing your Frigidaire Washer Door Glass
Customer Repair Stories
Glass broken
-
Lillian from PHILADELPHIA, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Glass inner door cracked due to machine rocking
-
Gennaro from Nutley, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
White in color.