This door handle for your washer is sold without screws, they can be ordered separately, or you can reuse the existing screws if they are in good shape. To replace this part, simply unscrew the handle and screw the new one into place.
This is a door bellow, also known as a door gasket or seal, that is compatible with washing machines. Door bellows are used as a method to seal the inner drum of the washing machine and the soapy water inside it, from the rest of the washer cabinet and your home. If you notice any leaks at the front of your washing machine, this door bell...Read moreow may be worn out or damaged, so inspect it to ensure it needs replacing. This door bellow is made of a thick rubberized material and wraps around the inner drum and will need a clamp to stay secure. This door bellow is sold as an individual OEM part and is not sold with any other parts or accessories.
This washer drain pump is a genuine replacement component designed for select front-load washing machines from Whirlpool, Maytag, Kenmore, and affiliated brands. It plays a vital role in the wash cycle by efficiently removing water from the drum, helping to prevent leaks and ensure proper drainage. A malfunctioning pump may result in slow...Read more or incomplete draining, water leakage, or error codes related to pump failure. This part is engineered for durability and reliable performance, and replacing it can restore optimal function to your appliance. Compatibility should be confirmed using your washer’s model number prior to installation.
This washer door lock and switch assembly is a critical safety and control component for front-loading washing machines. It secures the door during wash and spin cycles, preventing accidental opening and ensuring the appliance operates only when properly latched. The integrated interlock switch communicates with the washer’s control syste...Read morem to verify door status, helping prevent cycle interruptions and operational errors. This model features a four-lead switch for precise functionality and is compatible with a wide range of front-load washers. Replacing this part can resolve issues such as a door that won’t close, won’t open, or won’t lock, as well as a washer that fails to start. Installation should be performed with the appliance unplugged and may require basic tools.
Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Thomas Vonblohn - For model number GHW9150PW0
December 12, 2019
My washer won’t run it brings up
F. Dl
Hello Thomas, thank you for your question. That error code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won't run at all. We would recommend replacing PartSelect Number: PS11745016. I hope this helps!
3 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Elaine - For model number GHW9150PW0
November 19, 2024
My front load washer door wont close. i wash a big pillow and it hit something now it wont close. what parts do i need to have it fix
Hi Elaine,
Thank you for your question. If the door will not close after washing a pillow, you will need to check the door lock latch and strike as well as the door hinge. We would also recommend checking the inside of the door panel for signs of damage and check the door to see if it is out of alignment. Good luck with the repair!
Washer fill with water even when no in use. What part do I need to fix this.
Hello Harish, thank you for contacting us. According to our research, the issue seems to be with the water inlet valve, part number PS11744913. Sometimes, the water inlet valve solenoid gets jammed due to calcium deposits in the open position. You may also perform a continuity test using a multimeter to test the water inlet valve solenoid. We hope this solves your problem!
Hello Peter, thank you for getting in touch. According to our research, the error code F11 in whirlpool washer indicates a communication error between the motor control board, part number PS10064572, and the main control board, part number PS11745027. We would suggest checking the wiring connections between these electronic boards. If the issue remains, test both the control boards for continuity using a multimeter. You may have to replace either of the boards if found faulty. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken plastic washer door handle
541 of 550 peoplefound this instruction helpful.
dave from woodway, WA
Really Easy
Less than 15 mins
Screw drivers
Just required removal of two screws, placing the new handle and reinstalling the two screws. Easiest repair I've ever done!
Was this helpful?
Thank you for voting!
Bellows were moldy, needed to replace
371 of 399 peoplefound this instruction helpful.
Franck from Annandale, VA
Easy
15 - 30 mins
The first step is to remove the retainer ring that holds the outside of the bellow in place. To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up. You will fin
... Read mored a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow. Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.
The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily. When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow. Push as much of the bellow into the washer as possible to get it out of the way.
Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket. This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way. Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart. You can now remove the entire hose clamp from around the bellow by pulling it forward. You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out. Pull the old bellow completely out, very easy to do.
Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side. You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.
Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force. As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.
Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop. Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.
Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w
Read less
Was this helpful?
Thank you for voting!
Washer would not drain ,F02 and SUD code displaying
237 of 253 peoplefound this instruction helpful.
Donald from Wichita, KS
A Bit Difficult
1- 2 hours
Pliers, Socket set
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door. (3) I packed towels under the washer. (4) I slowly removed the cleanout i
... Read moren the front of the pump, using the water vac to catch the water as it leaked out. (5) I removed the wiring to the motor. (6) I removed the screw that holds the pump in place with a Torx T-20 socket. (7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ). (8) I tested the pump and found it would run but was making a lot of noise and running slow. (9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4). Don Kramer Wichita, Kansas
My Orders
