Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
GFE28GMKBES General Electric Refrigerator - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too co...
This NSF-certified water filter helps to improve the taste, quality, and health of your water by removing a number of contaminants including mercury, lead, and trace pharmaceuticals. The filter should...
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the sw...
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. This part has been updated by the manufacturer and may appear different t...
This door shelf bin is an authentic OEM part sourced directly from the manufacturer. It is designed for use in your GE refrigerator. It is made of white and clear plastic, and houses items on your ref...
This is a door handle fastener to secure the handle to your refrigerator drawer. It is also known and a mounting bolt or screw. It is approximately 1 inch in total length, and is made of metal.
This evaporator fan motor is a critical component in GE refrigerators, designed to circulate cold air over the evaporator coils and distribute it evenly throughout the fresh food and freezer compartme...
This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, e...
This OEM part is from GE and is designed for use in your refrigerator. This part is known as a door mounting screw, and is for mounting the handles of the refrigerator to the door studs.
This replacement vegetable pan glass is designed to restore the functionality and appearance of your refrigerator’s crisper drawer. It provides a sturdy, transparent surface for storing produce while ...
Designed for use in the fresh food section of compatible refrigerators, this LED light and cover assembly offers reliable, energy-efficient lighting using advanced LED technology. The clear, impact-re...
This is a door gasket for the freezer compartment of your refrigerator. Door gaskets are made of rubber and plastic and are designed to seal the cold interior of the freezer compartment from the ambie...
$62.50
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for GFE28GMKBES
Ask our experts a question about this model and we'll get back to you as soon as possible!
20 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred
September 13, 2022
sounds like an engine reving.... it last for about 5 to 10 minutes then stops. seems to happen only when the fridge starts a running cycle
For model number GFE28GMKBES
Hello Fred, thank you for your question. We have researched your model and found that the issue is probably with the run capacitor, part number PS11764031. If that does not take care of the issue, then the problem is most likely to be related to the evaporator fan motor, part number PS12172983. If you require assistance to place an order, please contact customer service. We hope that helps!
The air filter (part 930) is very blocked up with dust. How can i remove it so the compressor can stay cool when the house temperatures exceed 90 degrees in the summer?Also, although the water tray is dry, water is escaping and draining out on the floor. any ideas what may cause that?
is it possible to purchase a repair manual?
For model number GFE28GMKBES
Hello and thank you for writing.
Water tray dry sounds like the drain tubes PS12344758 might be clogged or damaged and need replacement or cleaning. The part number is shown as the condenser assembly. Is this the part you are trying to clean? If so we have attached the link to your manual, care instruction and so forth :
https://products.geappliances.com/appliance/gea-literature-search?Ntt=GFE28GMKBES&x=8&y=14
We hope this helps. Please contact us anytime if you require further assistance.
Frig not keeping things cold enough but freezer is fine.
For model number GFE28GMKBES
Hello Jane, thank you for reaching out. Based on our understanding of the issue, we would suggest replacing the temperature sensor, part number PS304103, to solve the problem. Glad to be of help!
I’d like to replace part 154
Can’t seem to figure out how to order
Thank you
For model number GFE28GMKBES
Hi Anita,
Thank you for your question. To order the drip tray, click the add to cart button and the part will be added to the cart. On the next page, choose the shipping option you would like. Then, on the next page, you would enter both your shipping and billing addresses and your credit card information. We hope this helps!
1 person found this helpful.
Did this question help you?
Thank you for voting!
Monica
February 7, 2020
How do you reset water filter
For model number GFE28GMKBES
Hi Monica. Press and Hold the Reset Button for around 8 Seconds. Thank you for your question and good luck with your repair.
Did this question help you?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.
I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more />After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.
I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the c
... Read moreatch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
