Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
GFE26JMMAFES General Electric Refrigerator - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too co...
This easy-to-install water filter improves the taste and quality of your fridge’s water by reducing lead, VOCs, and over 50 other impurities. NSF-certified for performance, it’s located in the upper-r...
This evaporator fan motor circulates air to the fresh food compartments for efficient cooling. It powers the evaporator fan that draws air from the refrigerator and circulates it over the evaporator c...
This compression ring is meant to hold the evaporator fan motor in place in the freezer compartment of your refrigerator. This is is a genuine OEM part. The tools needed to complete this repair are a ...
This part is the replacement door handle fastener for your refrigerator. It is made of white plastic and metal, is sold individually, and measures approximately 1-1/4 inches by 1 inch. The door handle...
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. This part has been updated by the manufacturer and may appear different t...
This door shelf bin is a genuine OEM replacement part designed for refrigerators. It is made of highly durable clear plastic, which allows users to easily view the contents of the bin. The bin is a st...
This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps to evaporate extra water in the drain pan.
If your refrigerator isn’t defrosting properly, the defrost thermostat may be the cause. This component plays a key role in regulating the defrost cycle by monitoring the temperature and signaling whe...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred
May 28, 2023
Water barely trickles out of water dispenser after changing the filter. Any ideas?
For model number GFE26JMMAFES
Hi Fred, thank you for the question. We have found that if the water filter was just replaced or installed, ensure the filter was installed correctly. If the water filter is not seated properly, it can cause water not to be dispensed properly. Try removing the water filter and reinstalling it. We hope this information is useful!
Did this question help you?
Thank you for voting!
Michael
February 17, 2024
IS THERE A A REPLACEMENT DISPENSER TRAY THAT CAN HOLD WATER?
For model number GFE26JMMAFES
Hi Michael, thank you for your inquiry. The drip tray you are looking for is part number PS12727298. Glad to be of assistance!
Fridge warm, freezer cold as it should be. Changed evap fan motor and tempature sensor. When the icemaker side door is closed there is NO air coming in from the freezer at rear of fridge compartment, but open the door and the and then the air starts coming out again. Close icemaker door and open freezer and cold air comes out at back of fridge. It sounds like a vent issue but how do I fix it?
For model number GFE26JMMAFES
Hello Shannon, thanks for reaching out to us. It might be that you have a build up of ice around the evaporator or in the cover where the vents are and air is not moving through properly. If you are looking to purchase this part then you can do so by either adding it to your cart and going through the checkout process online, or by calling our customer service line and ordering with one of our agents. I hope that helps. Good luck with your repair.
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.
I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more />After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.
I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
I had to remove all of the shelves.....part of the ice maker.....the rear cover over the freezer coils.....There were two wires that came from the back of the freezer that were also incorporated with the fan motor plug from the factory....This caused me to cut all of the wires from the new motor and soider them to the existing plug and sh
... Read morerink wrap the connections. If GE would have supplied two new ends I could have cut only those wires added the ends and inserted them into the new motor plug thus eliminating an extra hour and a soildering iron,,,,In my case not a big deal however not a project for those who have trouble with repairs using these type of tools.
