This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
This is a flood switch assembly for your washer. The flood switch controls the hot and cold water filling your washer tub to ensure the proper amount of water. You may need to replace this part if you...
This lower spray arm assembly in your dishwasher distributes water and detergent during the washing cycle by spinning around and spraying water in different directions. You can usually find it attache...
The element heating assembly is found at the bottom of the dishwasher tub, and helps to warm the water in the wash cycle, and dry the dishes afterward. If the water does not heat up during the wash cy...
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the...
This drain pump kit is for dishwashers. The drain pump kit removes the water from the dishwasher tub during the drain phase of the dishwashing cycle. The kit may include multiple parts; refer to your ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Peter
December 1, 2019
Do i have to use detergent in pods? Or can i use other types of detergent?
For model number GDT580SGF8WW
Hi Peter, thank you for your question. You would have to consult your manual, however generally most dishwashers can take any dishwasher specific detergent. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
We tried cleaning out the filter and it clogged with a huge amount of gunk. We removed the gunk, scrubbed the filter, and tried running the dishwasher, but still no water. That took over an hour (not counting the time the dishwasher spent running). Then we tried your diagnosis center and it pointed to the flood switch or the water valve.
... Read moreI extracted the flood switch (another 30-60 minutes) to check it, and it also contained gunk and (significantly) did not rattle, which made me suspect the flood switch was the problem, so I ordered one. Once the replacement arrived, I checked it and the flood switch rattled, confirming that it should work properly. I spent 30-45 minutes installing it, plus the filter assembly and racks I had to remove to access it. Ran the dishwasher and everything came out sparkling clean. I don't know where the gunk came from, but if you aren't getting water and the filter is full of gunk, check the flood switch.
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5.
... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.
Ran the diagnostic code test and no alarms turned on. Ran the heater test and it didn't turn on. I figured it was either the flood switch or the heating element itself. Removed and cleaned the flood switch and still nothing. Replaced the old flood switch and now it works like a charm. It took a minute to run tests and figure out a pl
... Read morean of action, but after ordering and receiving the part it was a quick operation to replace the old flood switch. Kill the power. Remove lower basket. Remove lower arm. Remove the coarse filter and the fine filter. Dry up water in bottom of dishwasher. Use 1/4" nut driver to remove two screws holding flood switch in place. Unplug old switch. Plug in new one. And put everything back. Saved a few bucks for sure. If I can do it, you can do it!