Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GCG1000-01

GCG1000-01 General Electric Trash Compactor - Overview

Get Parts and Repair Help for GCG1000-01

If you know the trash compactor repair part you need, you can browse the list of all parts on the GCG1000-01, or you can search by name or part description. You can also find your part by where it is located on the GCG1000-01 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your trash compactor. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the GCG1000-01

[Viewing 4 of 4]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.52

Single Roller

This is a single roller and it is a part for multiple appliances in your household. You may also know this as a bearing roller or a wheel assembly. It is roughly one inch by one in...

Order within the next 7 hrs and your part ships today!
$61.65

Trunnion Nut - Metal

The trunnion nut (also referred to as a power nut) is made of metal and sold individually. This nut is part of your trash compactor assembly. The trunnion nut has spiked edges and attaches to the side of the ram. When the power screw moves in a circular motion, it feeds through the nut, which pulls the ram down to compact the trash. Before beginning this repair, make sure your trash compactor is turned off. This is a genuine part that is sourced directly from the manufacturer.

Order within the next 7 hrs and your part ships today!
$27.77

SPROCKET 50 TOOTH

Order within the next 7 hrs and your part ships today!
$204.22

Gear Box Kit

This is a gearbox kit for a trash compactor. The outer casing of the part is made of metal and measures 5 inches wide and 7 inches tall. The gearbox is run by the motor, and allows the trash compactor to move up and down by the rotating gears. If you hear grinding or your compactor is not moving, you may need to replace this part. You will need to uninstall your appliance from the cabinet to complete this repair. You will need to disassemble the trash compactor drawer. This is a genuine part sourced from the original manufacturer.

Order within the next 7 hrs and your part ships today!
$4.23

WASHER THRST

Order within the next 7 hrs and your part ships today!
$51.54

Drive Chain

Also known as Endless Chain. Sold individually.

Order within the next 7 hrs and your part ships today!
$48.98

Bag Caddy

Order within the next 7 hrs and your part ships today!
$21.08

Turn Bearing

$6.82

NUT SNAP-IN

$6.59

BRNG REV TST

Common Symptoms of the GCG1000-01

[Viewing 1 of 1]
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Compactor Piston stays down even though the motor is running

  • Customer: Robert from San Deigo, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 15 of 19 people found this instruction helpful
If the drawer is stuck because the piston is in it, you will have to take the back off to lift the piston in order to remove the drawer.

With the drawer out, tip the compactor on its back to easily maneuver the otherwise heavy piston. Working from the front remove the trunnion nut cover (two hex screws) and then the bad trunnion. You may need to m... read more

Plastic trunnion nut was worn out

  • Customer: Joe from Avondale, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 10 of 12 people found this instruction helpful
The problem with this repair arises after you have removed the old trunion nut and you are trying to get the new one to seat into the narrow bracket that surrounds it and keeps it from turning. You can only screw the trunion nut on so far and then it runs into the edges of the bracket. I found that by aligning the new trunion nut at the proper angle and then... read more

The ram would not raise and the motor kept running.

  • Customer: Scott from Colleyville, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I actually pulled the entire motorized unit out of the case, not knowing what the problem was. I found that the old nylon trunnion nut was stripped. I ordered two replacement trunnion nuts in case the replacement stripped out also. (However, the manufacturer has replaced the old nylon nut with a threaded metal unit that should never strip so I goofed when... read more