Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This dishwasher door gasket (Bottom Gasket, Gasket, Door Seal, Dishwasher Door Lower Seal) helps prevent water from leaking out of the bottom edge of your dishwasher door by creating a watertight seal...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwasher. No tools are required for this repair, simple remove the rack stops and u...
This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the de...
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the baske...
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, ...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely ...
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
This dishwasher door latch assembly is a critical component designed to ensure safe and efficient operation. It features an integrated switch that functions as an on-off mechanism, preventing the appl...
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
January 7, 2020
Error code "uo"
Please explain what this means
For model number FGHD2465NF0A
Hello Gary,
Thank you for your question. The UO error code means "Vent Open". On the top back right corner of the dishwasher tub, there is a vent and fan that opens to help dry the dishes at the end of the cycle. If the computer senses that the vent is open, then it won't start the cycle. Frigidaire says to first check the wiring and connections. If the wiring and connections are good, then you should first replace the vent assembly. If that doesn't solve your problem, then you should replace the main control board under part PS6012231 for your model. We hope this helps!
Water is left in bottom of dishwasher after cycle. I have repeatedly removed all bottom filters and removed all debris. I have also removed drain pipe from under sink and used shop vac to suck all water from dishwasher. All water comes out with no problem. So what might be wrong?
For model number FGHD2465NF0A
Hi Audrey, thank you for the great question. Standing water in your dishwasher after a wash cycle means that your dishwasher isn't draining properly. This is because leftover food is clogging the drainage system. Inspect your dishwasher, and clean the drain basket. If this doesn't take care of the problem, you may have a clog in your drains. If there is more than a little standing water a new drain pump part number PS8689824 could be next. We hope this helps.
MY DISHWASHER is on but doesn't start the cicle.what can I do
For model number FGHD2465NF0A
Hello Francisco, thank you for reaching out. We have concluded that the issue is with the door latch, part number PS16218716. It prohibits the dishwasher from operating when the door is open. You will need to inspect it to fix the issue. Good luck with the repair!
Hello Hulene, thank you for your question. ER Error Code is a membrane switch failure. Main control has detected a stuck key or a key pressed for more than one minute. Check connections. If correct replace key pad. (White) PS8760853 (Black) PS8760855 (Black with Silver trim) PS8760856. If problem still exists replace main control. Part number PS12365809. We hope this helps.
I accidentally held the delay start button and cannot get the green light to go off so I can actually start the dishwasher now!!!! Please send me instructions to fix!!
For model number FGHD2465NF0A
Hello Fran, thank you for reaching out. According to our research, to cancel the delay start option and begin the cycle before the delay period is over, press the START/CANCEL pad. We hope this information helps!
Did this question help you?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having th
... Read moree problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it
... Read moreleaked in the first place and messed up my subfloor and laminate flooring.
