Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The upper dishrack is used to hold your dishes in place while the dishwasher goes through the wash cycles. Over time the dishrack can become damaged, start to rust, or be missing rollers, and the dish...
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the baske...
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, ...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
This dishwasher door latch assembly is a critical component designed to ensure safe and efficient operation. It features an integrated switch that functions as an on-off mechanism, preventing the appl...
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete i...
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plasti...
$100.02
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for FFID2426TS2A
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Nicky
February 3, 2024
Why 3 lights are blinking?
For model number FFID2426TS2A
Hello Nicky, thank you for reaching out. According to our research, the blinking lights indicate that there is a problem with the door latch. We would recommend checking the door latch. If it is not faulty, then you may need to replace the user interface control button assembly, part number PS12585991, to fix the issue. We hope this solves your problem!
I WAS HOP[ING YOU COULD TELL ME HOW OLD DISHWASHER IS NEEDS REPAIR WASHING CLEAN SUNITIZED LIGHTS STAY ON AND WONT START
For model number FFID2426TS2A
Hello Dan, thank you for reaching out. When the washing, cleaning, and sanitizing lights all flash simultaneously, it can be an indicator that the flood switch has been activated. You will find that the emergency pan has suds or water in it. Typically, this is caused by overflow from suds or an incorrect drain hose setup. The drain hose should be placed as high as possible to prevent the sink from backing up into the dishwasher and regular dish soap residue from entering the dishwasher. If you use the wrong kind of detergent, it will cause excessive suds to overflow into the pan. You can try using a wet or dry vacuum to drain the pan. Otherwise, you may have to maneuver the dishwasher around and tip it back to drain the pan.
Did this question help you?
Thank you for voting!
Rachel
November 6, 2024
Do you sell just the overlay sticker for this model? The start button has worn on my panel.
For model number FFID2426TS2A
Hi Rachel, Thank you for writing. The Overlay is only sold as part of the Console Assembly with Overlay, PartSelect Number PS12585994. We hope this helps!
Dishwasher blows its own 20amp breaker
into the wash. Tried another 20 circuit blows it also. Once blown i notice water at bottom of tub.
?is it blowing due to the heating element and stopping cycle before pump out cycle?
What else once the wash cycle starts can draw more than 20amps?
For model number FFID2426TS2A
Hi Rich, Thank you for writing. This can be caused by a faulty heating element, damaged wires or a faulty Door Switch in the Latch. We hope this information helps!
Hello Luis, thank you for reaching out. The rinse aid dispenser cap for your model does not come separately, and it comes as a part of the detergent dispenser assembly, part number PS11770487. We hope this helps!
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
The hardest part was disconnecting the dishwasher. the motor is located on the bottom so after pulling it out and laying it down on the front of the machine the motor unplugs and 2 screws hold it in place.The new motor comes with "O" rings so I applied a little grease and put it back together. 2 minutes to replace motor, 15 minutes to dis
... Read moreconnect water and electric, 15 to reconnect.
