Models > FEN500WXXAA

FEN500WXXAA Samsung Range - Overview

Sections of the FEN500WXXAA

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Ceramic Fuse - 20 amp – Part Number: WPM0805101
Ceramic Fuse - 20 amp
★★★★★
★★★★★
(3)
PartSelect #: PS11747931
Manufacturer #: WPM0805101
This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave w...
$10.76
  In Stock
Range Oven Temperature Sensor – Part Number: DG32-00002B
Range Oven Temperature Sensor
★★★★★
★★★★★
(5)
PartSelect #: PS4240743
Manufacturer #: DG32-00002B
$86.21
  In Stock
Rubber Cushion – Part Number: DG73-00003A
Rubber Cushion
★★★★★
★★★★★
(1)
PartSelect #: PS4241222
Manufacturer #: DG73-00003A
Sold individually.
$6.57
  In Stock
THERMOSTAT;-,NT-101,250V – Part Number: DE47-20037A
THERMOSTAT;-,NT-101,250V
★★★★★
★★★★★
(4)
PartSelect #: PS4226434
Manufacturer #: DE47-20037A
$19.79
  In Stock
Range Convection Fan Motor Assembly – Part Number: DG96-00110E
Range Convection Fan Motor Assembly
★★★★★
★★★★★
(6)
PartSelect #: PS11720787
Manufacturer #: DG96-00110E
The convection fan motor spins the fan blade to circulate hot air through the oven for even heating.
$129.76
  In Stock
Convection Fan Motor – Part Number: DG31-00005A
Convection Fan Motor
★★★★★
★★★★★
(6)
PartSelect #: PS4240735
Manufacturer #: DG31-00005A
The fan motor helps rotate the upper fan blade to circulate the hot air though the oven cavity for even heating. This motor is reverse threaded.
$106.15
  In Stock
RACK ;FLAT;FE;FTQ;FCQ,MWSR-SWRM,629,41 – Part Number: DG75-01001C
RACK ;FLAT;FE;FTQ;FCQ,MWSR-SWRM,629,41
★★★★★
★★★★★
(3)
PartSelect #: PS7321783
Manufacturer #: DG75-01001C
$160.41
  Special Order
HEATER-RADIANT DUAL;FTQ* – Part Number: DG47-00043B
HEATER-RADIANT DUAL;FTQ*
★★★★★
★★★★★
(1)
PartSelect #: PS4240841
Manufacturer #: DG47-00043B
$197.31
  In Stock
Hexagon Nut Cap – Part Number: 6021-001211
Hexagon Nut Cap
PartSelect #: PS4133540
Manufacturer #: 6021-001211
Left hand thread.
$9.14
  In Stock
Convection Fan Blade Spacer – Part Number: DG60-00001A
Convection Fan Blade Spacer
PartSelect #: PS4240847
Manufacturer #: DG60-00001A
$6.57
  In Stock
SCREW-TAPPING;PH,+,NO,2S – Part Number: 6002-000630
SCREW-TAPPING;PH,+,NO,2S
PartSelect #: PS4133229
Manufacturer #: 6002-000630
$4.04
  In Stock
FAN-CONVECTION MAIN;FSE1 – Part Number: DG67-00018A
FAN-CONVECTION MAIN;FSE1
PartSelect #: PS4241128
Manufacturer #: DG67-00018A
$17.63
  In Stock

Questions And Answers for FEN500WXXAA

Be the first to ask our experts a question about this model!

Common Symptoms of the FEN500WXXAA

[Viewing 2 of 2]
Won’t turn on
Fixed by
these parts
Show All
Little to no heat when baking
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
microwave oven blew fuse
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
Parts Used:
Ceramic Fuse - 20 amp
  • tad from tamarack, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
23 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microve stopped working
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise
Parts Used:
Ceramic Fuse - 20 amp
  • Denice from Montgomery, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
12 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave went pop and nothing would work.
I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.
Parts Used:
Ceramic Fuse - 20 amp
  • Deborah from STRUM, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!