Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely ...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the door drops too quic...
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete i...
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plasti...
This lower dishrack assembly is a genuine replacement component designed to restore full functionality to your dishwasher. Made from durable, rust-resistant materials, it securely holds dishes, cookwa...
$87.26
In Stock
Order now and your part arrives by Jun 4
Questions And Answers for FDPC4221AW0A
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sharon
May 30, 2024
How do I remove and clean the filter #5304506525 at the bottom of the tub?
Would the Serial # work?
For model number FDPC4221AW0A
Hello Sharon, thank you for contacting us. We have attached a relevant video that may not be of the exact model, but will help you in removing the filter. After removal, you may simply need to rinse it with hot water in order to clean it. Glad to be of assistance!
1 person found this helpful.
Did this question help you?
Thank you for voting!
Jennifer
January 21, 2023
dishwasher has water to water inlet valve...replaced value but no water to inside the dishwasher. you can hear the motor running. What part do i need to replace next?
For model number FDPC4221AW0A
Hello Jennifer, thank you for contacting us. The issue is probably related to a faulty float switch, part number PS3492842. It shuts the water fill valve off if the water level gets too high before the timed fill cycle ends. If it is faulty, the water inlet valve can remain shut. We would also recommend checking the float assembly, part number PS11770486. Customer service is available seven days a week if you require assistance placing an order. Thanks again for reaching out!
Do you have a replacement rinse aid cap for this model? Or where can I get one?
For model number FDPC4221AW0A
Hello Heather, thank you for reaching out. We have researched your model and found that the rinse aid cap is not sold separately. It comes as an assembly with the detergent dispenser, part number PS11770487. We hope this is what you were looking for!
The replacement rack shown in the picture here doesn’t show an upper spray arm attached to the underside of it like the one has in the machine I am replacing. So does the spray not come with the upper rack and is it something I can remove from my old rack and install an the new one?
For model number FDPC4221AW0A
Hello John, thank you for your question. Yes the new Rack PS17219659 does not come with the sprayer attached. You will need to remove it from the old rack and reattach it to the new one. We hope this helps.
Hi Ken, thank you for your inquiry. Check the dishwasher filter, part number PS11770489. If the filter is clogged or full of debris, clear it as it can affect the water flow. If the heating element, part number PS3653449, is weak or not working efficiently, the dishwasher will take time to heat water properly for the wash cycle. You can check the heating element visually and also do a continuity test using a multimeter. Glad to be of help!
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the t
... Read morehing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
